Jump to content
SAU Community

Recommended Posts

hi all,

well i got defected today, the following "faults" were found.

-bov under bonnet

-wheels and rims 3inch oversize

-no clearance between body and top of tyres

-not comply with 100mm clearance

-no tyre placcard

-oversize exhaust

-loose wires under passenger floor mat.

can someone whos been through this tell me will i get a fine for each and every point listed above? As "no clearance b/w body and top of tyres" and "not comply 100mm clearance" are the same thing! ie too low!

and oversize exhaust?! WTF is that?! isnt it the noise level not the size of the pipe that matters?

It says i have to clear it via a FULL INSPECTION. Whats the deal here in NSW- if i fix the problems on the current defect, will they just go over the car and send me home with another dozen things to fix?

If thats the case then ill just drive it back to SA and do it there, at least i have all the tools/parts there.

cheers

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/
Share on other sites

1. BOV is illegal, no two ways about it

2. Technically, if the wheels are more than an inch wider or larger than stock, they require an engineers sign off to be deemed safe and accapetable

3. There is no clearance rule in terms of tyres & guards to my knowledge, other than no part of the wheel or tyre should foul/scrub on any part of the inner guard or suspension. If it does, and there are marks to prove it, then there are grounds for a defect

4. You need to have a tyre placard, the fact you dont have one will more than likely cause the officer to further doubt the legality of your wheels and tyres, particularly when they probably have no idea what size the car came with factory

5. If the officer suspects your exhaust is too big or too loud, they can send you to the EPA for testing to ensure your exhaust complies with the DB limit. To clear it either replace your exhaust with a standard system for testing or try and quieten your existing exhaust down to a suitable level.

6. Loose wires? Odd one - police normally wouldnt go to such effort when defecting so obviously it just wasnt your day. Try and clean the wires up

The end :)

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-903974
Share on other sites

i didnt exactly get defected for doing nothing, i was having some fun at the time which drew attention to myself.

The defect category is "MINOR" and says it must be cleared at an AIS (authorised inspection station)

-What/Where is an AIS? Is it like a registered workshop/garage? or is it a full RTA depot place?

-Also where would i get a tyre placcard?! They mustve left it off after the respray.

-And again, does anyone know if the defects are subject to a fine?!

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-904401
Share on other sites

Yup give your local RTA a call and they will be able to give you the address of some local work shops to clear it for you. From memory the cost is $20 for them to sight your vehicle and pass it, no fine (from memory a fine would be stated on the defect notice).

Just fix the minor things and then rock up with a case of beer in the passenger seat and see how you go. Theirs nothing proving that you didn't change things 'back' to what they currently are after you left the AIS.

:D

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-904614
Share on other sites

if they haven't given you fines on the spot then you are pretty much all clear...

also, give the rta a call, because when i got defected and still had qld rego i called both the cops & the rta to see how i could get it cleared and both of them said that they couldn't clear the defect cos it was a qld registered car.....so i called qld transport & they said that they couldn't do anything because the defect was issued by nsw police

so i took it to the AIS that is currently in my garage & engineered it myself......read: i took off the canary & never heard from the cops/rta about it again

Link to comment
https://www.sau.com.au/forums/topic/44232-defect-helpadvise/#findComment-905175
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...