Jump to content
SAU Community

Recommended Posts

For sale:

Kaaz Super Q 2 Way SAN3510 $750

Been on the car for about 5000 kms, pulled out because I bought a dedicated drift car shortly after installing it so it was only getting daily driven.

Project Mu Handbrake shoes IS200B $150

Brand new in box, never installed for reasons stated above. I have them on the R32 though and they are awesome.

Doug

0402838265

post-113720-0-09676400-1398581710_thumb.jpg

post-113720-0-10787400-1398581970_thumb.jpg

Edited by Choppa7

I'm not interested, but for people who are, what does the Diff suit?

Open and VLSD output shafts are different, so the diff that it came out of was originally a ............?

I'm not interested, but for people who are, what does the Diff suit?

Open and VLSD output shafts are different, so the diff that it came out of was originally a ............?

Googling that model number up top would answer that question

It's for a 350Z VLSD so the 6x1 output shafts standard on 300Gt and above

Edited by Howaitonaito

Googling that model number up top would answer that question

It's for a 350Z VLSD so the 6x1 output shafts standard on 300Gt and above

Well done... But the difference is on the inside, not the stud pattern. Vlsd have three sets of splines, open, two. ;)

You should buy it. It would rip skids. The vlsd isn't going to last behind the LS. :)

Your not going to blow it up, it's just got going start single spinning like a dirty VS commo.

This would chirp carparks like a Baws, and we know you like hardparkin carparks.

  • 2 weeks later...
  • 2 months later...
  • 5 weeks later...
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • f**king around with the bro
    • Ludenham   44.2 tops day no issues  
    • Then today, I went to visit a man with an r33 hat Peter and Road and Race sorted the alignment. As it is being set up for general track/hillclimbs etc it has a heap of caster (7o), less camber than I am used to (1o front and 2o rear, as the caster looks after that in turns without the braking downsides), 3mm front toe out and 0 toe rear. Will see how that goes and track tyre wear to see if it does need more camber, but adjsustment is also limited with nismo arms and adjustable bushes at only 1 end. It does have a bent inner tie rod on the driver's side front but as it came up within spec I'll just leave that as is. So, that is getting close to my chapter of this story....could of tidy ups then a shakedown in early October before it finds a new home.
    • So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
    • what sort of caliper are they? If they are a slider and you gave everything a good clean, you might need to regrease the pins. My guess though is they will come good after some abuse as suggested above
×
×
  • Create New...