Jump to content
SAU Community

Recommended Posts

Hey guys for sale is my GENUINE Trust/Greddy TD06SH 25G 8cm (responsive). This comes with the whole kit including the

Greddy turbo

Greddy exhaust manifold

Greddy external waste gate

Greddy dump pipe

Greddy exhaust housing heat shield

4inch intake

All the braided lines and fittings

All gaskets and bolts

This is an outstanding setup, all made to work together for best performance. The compressor housing is professionally sprayed black for stealth and a neat look.

Its still fitted to the car so u can come test it before i get it removed. Its seriously an awesome turbo kit for the rb engines.

For fitting you can just unbolt the manifold from the head and unbolt the dump form the rest of the exhaust and drop it in your engine. CANT get more bolt on that this.

Its don't very little work. Was installed march 2013 when the whole car got built and only had 5-7000km on the motor on street, was more of a show car.

Made a very strong 320rwkw on 18psi. Easy 360+ on e85.. Not for the faint hearted i should say

Only reason for sale is that I'm going a different direction with the whole car and motor.

Asking $3500 (brand new retails close to 7k) … grab a bargain

contact Andrew on 0450232121

Melbourne but can't post very cheap

Also have a matching intercooler and piping, and also a 3.5 inch HKS exhaust for sale too if your interested. All already on the car and can be tested.. Get in before i remove them :)

post-72334-0-84654700-1399046565_thumb.jpg

post-72334-0-33148500-1399046573_thumb.jpg

post-72334-0-39467700-1399046718_thumb.jpg

Hey mate I take it this is for an RB26dett cylinder head?

I'm currently running a rb30dett setup in an r32 GTR and looking to go to single turbo.

Currently running 22psi with twin HKS 2530's.

couple questions:

1) will this fit r32 GTR?

2) can you post a pic of the turbo installed in the engine bay - want to get an idea of clearances because my cylinder head is sitting 38mm higher. Ideally, can you post a pic of the height of the turbo/plumbing relative to the height of the rocker covers? (ie like the photo you have but from a lower angle, it's hard to tell how high the turbo sits)

3) does this include some kind of dump/front pipe setup to connect up to the stock cat converter position?

4) what is the diametre of the outlet on the turbo? Does it have some way to connect to the stock intercooler setup?

Edited by dorifticon
  • 2 weeks later...
  • 9 months later...
  • 1 year later...

Back up for sale again.

Kit now includes:

Greddy turbo (8cm rear housing)

Greddy exhaust manifold

Turbosmart Hypergate45mm external waste gate

Greddy dump pipe

Greddy exhaust housing heat shield

All the braided lines and fittings

All gaskets and bolts

Now fitted to my r34 gtt and still in the car so if you are early you can get a test drive. Making 322rwkw on 18psi on BP98

Reason for sale is going bigger turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...