Jump to content
SAU Community

Genuine Garrett Gt3076R

bubbabooga
 Share

Recommended Posts

bubbabooga Rising Star

bubbabooga

Posted
Posted

As title states

Genuine garrett gt3076r turbo with .63 exhaust housing which is also ceramic coated.

Has the surge slots in the compressor housing.

Done minimal use and bearings etc are still in brand new condition.

Chasing $1100ono

Needs to go to pay for my 26/30

Located near adelaide Sa but am Willing to post at buyers expense.

Msg Tom on 0423420713

For picitures

Cheers

Link to comment
https://www.sau.com.au/forums/topic/443197-genuine-garrett-gt3076r/
Share on other sites
  • 2 weeks later...
bubbabooga Rising Star

bubbabooga

Posted
  • Author
Posted

Adding -

SARD 700cc twin spray top feed aka rb26/20.

Injector bases were hand polished before I got them. They have been cleaned twice since removal whilst fault finding.

Selling to upgrade to ID's.

like new condition.

$500ono

Message Tom on 0423420713 for more pics or details.

Cheers

  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...