Jump to content
SAU Community

Recommended Posts

Hey everyone!

New to the forum obviously, however I have often come here over the years for tips and advice and i'd like to thank you all!

Owner of a R31 1989 Skyline Silhouette for the past 13 years and just in the last few days acquired a 2003 Stagea NM35 250t RX to keep her company ...so i'm a newb to turbo engines and imports ...can't believe how much of a pain the stock Bose system is to repair/replace! Ripped the existing unit out to give a few love-taps to see if the CD's would un-jam but to no avail ...i'm happy listening to the engine for now while i get used to it all. Also have noticed rough idle/surging at startup combined with black smoke from exhaust for up to 5 minutes when cold and after sitting for a few hours ...within 10 minutes the surging subsides ...could it be an oil seal somewhere? Love my Nissans but in no way a mechanic, though not afraid to give repairs a go. Have already scoured the forums for possible solutions but haven't seen the exact same issue yet ...any ideas anyone?

Glad to be a forum member finally :)

Cheers!

IMAG0210.jpg?dl=1&token_hash=AAEvsPs6HB7

20140322_190017.jpg?dl=1&token_hash=AAHm

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/443643-nissan-obssessed/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...