Jump to content
SAU Community

Recommended Posts

Updated Sun the 22nd...( from WA..)

1 x set of motorsport steel wheeled Factory N1 turbochargers - bolt straight on - excellent condition -Now $800

1 x Apexi Power FC c/w hand controller - excellent condition - Now $800

1 x OS Giken - twin plate/pressure plate/flywheel package- used condition -Now $600

2 x std airboxes - bottle of boubon :cheers:

or 2k for the lot!!

  • Like 2

I would say 35% left on clutch plates...

I bought the new OS&G twin plate set up c/w flywheel for $2300.

Used it for a few thousand klm's( race klm's)..

Very streetable combo( can do hill tsarts etc without bunny hopin..)

Have upgraded to a single pup clutch based on a new 600-ish HP engine combo..( which is not very streeatble and will not do hill starts- but more suitable and race orientated..

You can buy OS&G clutch rebuild kits- check these costs out first and then you can see an all up cost for a totaly new package

  • 4 weeks later...

Not much feedback on the R32 GTR OS&G twin plate or Apexi Power FC....revised pricing below...

Apexi pwer FC with hand controller now $500( I have replaced my Apexi with a Haltech unit-which gives me data aquistion capability)

OS&G twin plate and flywheel complete package - make an offer see pictues below:

post-74499-0-72044700-1406356863_thumb.jpgpost-74499-0-38926800-1406356882_thumb.jpgpost-74499-0-24488100-1406356900_thumb.jpgpost-74499-0-06418500-1406356927_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...