Jump to content
SAU Community

loosing my power steering

ImPrOvIsE

By ImPrOvIsE,
in Western Australia

 Share

Recommended Posts

ImPrOvIsE Collaborator

ImPrOvIsE

Posted
Posted

Gday all. Lately I have been losing my power steering. Sometimes the car will start with the power steering working and then it will conk out (power steering stops working while drviving)..I can still drive like this but Im sure its not good for the car drving without power steering. Other times it wont work as soon as I start the car.

THis has been happening since the HICAS light has been appearing now and then on the dash.

So far I have checked the obvious things. Power steering fluid, HICAS connections underneath car and the HICAS fuse.

My car is an R33 gtst.

Anyone got any ideas?

cheers

Link to comment
https://www.sau.com.au/forums/topic/44583-loosing-my-power-steering/
Share on other sites
R34 Mentor

R34

Posted
Posted

Had a problem with my Hicas computer under the rear parcel shelf.

The compliancer got it wet (don't know how).

It had the same symptoms as yours until I dried it out and it started working again.

So I'd say check that computer first.

If the steering pump is turning without fluid spewing out it's unlikely to be the pump I'd say

Good Luck

  • 6 months later...
ImPrOvIsE Collaborator

ImPrOvIsE

Posted
  • Author
Posted

going to have to resurect this thread guys. The problem I was having with losing the steering disapeared not long after posting the previous post. THe problem has now come back. Basically when the hicas light comes on I lose power steering but it can come on and off at its own will which is quite dangerous when turning corners obviously.

Can someone please help with this. I have tried a hundred and one times to get into diagnostic mode and just cant seem to do it.

cheers

  • 4 weeks later...
Mickroy Collaborator

Mickroy

Posted
Posted

hmm... I'm actually having a similar problem. It started with driving with my dash taken off. Power steering would work for a while, then stop working, then hicas light would come on. Once I put the dash back together, it went away.... Now, some months later, its happening again. Power steering will turn off after about 10 mins of driving, and hicas light will come on in a further 5 mins. Im stumped :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...