Jump to content
SAU Community

Recommended Posts

Hi guys. I still got some spare parts left.

I really want to get rid off them as they are just sitting in the garage collection dust and it could be useful to somebody.

dirt cheap!!!

- standard clutch and pressure plate (fairly good condition) $40

- standard M-spec front bar (white). I cut the middle part of the bar off to get better air flow to the FMIC. not a very clean job but little bit of work can make it nice. Sale for $40 SOLD

- Standard gear nob (abit worn) $10 SOLD

- Standard intercooler with pipes very good condition $60

- Standard dump pipe and Cat. $20 SOLD

- Spitfire boost gauge read up to 20psi. only used for 3 months. Bought for $130. sell for $60

- Turbo smart boost controller. bought for $100 bux only used for 3 months. Sell $40[/color] Lost, No longer for sale

- 3 Goodyear Eagle F1 tyres 215/40/17 50% tread left. 3 for $30 SOLD

- Standard boost controller. $10

- stanless exhaust tip ( not sure if its 2.5 or 3 inch) . very good condition $80

- Philips Tape and Radio player. $20

- A few Neon Lights & etc.... $15-30

call 0414228278

Link to comment
https://www.sau.com.au/forums/topic/44639-dirt-cheap-r33-parts-sydney/
Share on other sites

vioty33

the cooler doesnt have the complete piping. It only has one section.

give me ur email address. so I can send some pics to you.

I will only send it interstate if you direct deposit the money to my bank account first.

hwystar

I shipped the monster size FMIC kit and only cost me 55 bux, so it should be less than 30 bux.

BOOSTD

I will give u a call on the weekend. ( I hope I can still find it...)

* The tyres are sold

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...