Jump to content
SAU Community

Recommended Posts

Wrecking R32 GTR 91 & 94

- Gates RB cam gears, minimal use have 2x sets $250 per pair

- RB26 Head Damaged (check link for more info) $400 http://www.ebay.com.au/itm/231303544661?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

- Mines 320km/h dash (Blue circuit) $350

- Impul 300km/h dash (Blue circuit) $300

- Gizzmo launch control w/shift light $300

- Schroth harness (out of date) $40

- R32 Gtr boot no wing $50

- R32 Gen front windscreen with aerial $250

- R32 3.5" Catback exhaust Jasma Gtr Gts-t Gts4 $200

- R32 Gtr bonnet with Gen N1 lip, needs respray & 2x small dints $450

- R32 Gtr Rear seats good cond $120

- R32 AFM's $100 for the pair

- M's filters & adapters $125

- Panasport G7 17x9's with tyres(2x tyres need to be changed due to incorrect rolling dia) $1000

- 6" K&N filter $40

- Std rb26 plenum $125

- 2x Gearbox's 1x Push 91' 1x Pull late 94' $500 each

- R32 Gtr BM50 master cyl $80

- R32 Gtr rear side boot trims (with holes for adjusting coilovers) $$FREE

- 2x Brand new red Bride copy carbon Vios low max seats with rails (they need rail adapters to suit your specific car) $350 each

- R32 Tail lights $50 each

- CAS unit $50

- Rear and front shafts $80 each

- Abs unit $100

- Factory ecu $140

- Alternator & starter $80 ea

- Heaps more parts avail

Pick up in Eltham, Vic 3095 or can post.

PM or Email for more info/pics [email protected]

OR call/sms 0417 125 253 Elliot

post-18664-0-85932300-1407654497_thumb.jpg

post-18664-0-79173100-1407654521_thumb.jpg

post-18664-0-58555000-1407654574_thumb.jpg

post-18664-0-39981900-1407654982_thumb.jpg

post-18664-0-43080200-1407655014_thumb.jpg

post-18664-0-51132500-1407655034_thumb.jpg

post-18664-0-33843900-1407655057_thumb.jpg

post-18664-0-86677000-1407655091_thumb.jpg

post-18664-0-41098500-1407655118_thumb.jpg

post-18664-0-22404900-1407655150_thumb.jpg

post-18664-0-79034900-1407655174_thumb.jpg

post-18664-0-62686800-1407655185_thumb.jpg

post-18664-0-32135000-1407655219_thumb.jpg

post-18664-0-84446800-1407655243_thumb.jpg

Just curious if the plenum comes with the throttle bodies and linkages etc??

No, I can do the plenum with throttles and linkages for $300

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...