Jump to content
SAU Community

Recommended Posts

Hi everyone,

All the following parts are from my 1995 Series 1 R33 GTR V Spec, following a recent upgrade.

Please refer photo's for what's included with each item.

DBA 4000 Rotors (4298SL) Front (when new 324mm x 30mm) Rear (new 300mm x 22mm), with Endless CCX pads (BL12BL rear, BL09BL front), stock R33 GTR callipers & lines. $1,400.

Stock R33 GTR twin turbos, off running engine set to 1 bar boost. Minimal shaft play & appear pretty good condition. Includes actuator, dump pipes & heat shields. 85,000kms old. $200.

R33 RB26 14 x standard head studs. $40.

R33 RB26 6 x standard injectors. $60.

R33 RB26 water pump. $20.

R33 RB26 oil pump. $90.

R33 RB26 6 x pistons & 5 1/2 x rods (No freakin idea what happened to the other half of the rod! Turned my place upside down looking for it.) $100.

R33 RB26 6 x standard coil packs. $100.

R33 RB26 cam gears. $40.

R33 RB26 tension & idler pulleys. $50.

R33 RB26 standard harmonic balancer. $50.

R33 RB26 crank angle sensor. $150.

HKS EVC IV (Electronic Valve Controller/Boost controller). $290.

R33 GTR Power FC & hand controller. $700.

I live in Rockdale NSW.

PM me with any further inquiries.

post-59440-0-87336800-1413292965_thumb.jpg

post-59440-0-70446400-1413293233_thumb.jpg

post-59440-0-03097600-1413293284_thumb.jpg

post-59440-0-64091300-1413293338_thumb.jpg

post-59440-0-89287200-1413293393_thumb.jpg

post-59440-0-10786600-1413293458_thumb.jpg

post-59440-0-85191600-1413293517_thumb.jpg

post-59440-0-68981800-1413293578_thumb.jpg

post-59440-0-23691900-1413293639_thumb.jpg

post-59440-0-28515100-1413293692_thumb.jpg

post-59440-0-76900600-1413293738_thumb.jpg

post-59440-0-62919900-1413294509_thumb.jpg

post-59440-0-11124100-1413294580_thumb.jpg

post-59440-0-12035300-1413294641_thumb.jpg

post-59440-0-04281000-1413294703_thumb.jpg

post-59440-0-33304100-1413294752_thumb.jpg

post-59440-0-45816700-1413294809_thumb.jpg

post-59440-0-05198600-1413294859_thumb.jpg

post-59440-0-03640200-1413294914_thumb.jpg

post-59440-0-80094300-1413294969_thumb.jpg

post-59440-0-29807900-1413295022_thumb.jpg

post-59440-0-14977000-1413295178_thumb.jpg

post-59440-0-05754200-1413295219_thumb.jpg

post-59440-0-89686800-1413295275_thumb.jpg

post-59440-0-03410200-1413295317_thumb.jpg

post-59440-0-33326100-1413295383_thumb.jpg

post-59440-0-08344000-1413295433_thumb.jpg

post-59440-0-10837000-1413295490_thumb.jpg

PM's replied. A lot of interest in the Brembo's.

Initialdennis I will separate if someone doesn't buy the whole setup.

Nice teamwork guys, I have an interested buyer looking at them tonight. If unsuccessful I'll let you know.

Initialdennis, I went AP Racing & have never looked back! But as always it's dealers choice. Good luck hunting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...