Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey mate, chasing left rear CV shaft, 6x1 600mm 29 splines (29.5mm diam). If you have one but with more/larger spline section, I would also need the hub and bearing etc to match so I can bolt it up...

RB25 box - $1000

RB26 blitz intake -$250

Rb26 Nistune - $400

GTR cooler - $80

R32 door silver - $50

R33 door black - $50

R32 GTR grill and bonnet latch - $200

Turbosmart and boost fx Bov - $50 each

R32 GTR loom uncut & complete - $200

32 GTR seats front and rear set - $600

GTR injectors x6. (440cc) -$100

HKS turbo timer -$30

32 GTST bonnet latch support -$30

26 STD coil packs -$40

6 x top gun 10mm leads -$100

RB20 Bov adaptor -$30

33 boss kit with steering wheel -$100

2 x Peterson 600 series fuel filters with mounting bracket -$350

R33 Gtr window switch by itself -$30

R32 mudflat set -$50

R32 GTR tan gear stick boot and glove box lid set -$100

32 GTR rear floor mat -$30

4 inch intake with k&n filter brand new -$100

32 GTR STD intercooler piping -$100

RB26 TOMEI computer -$400

Twin 044 proflow pump bracket -$30

Rb26 fuel rail dual -8 feeds with -6 return ... Fittings attached $50

R33 GTR Std Bov pair - $100

Parts list updated as to what's still available

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...