Jump to content
SAU Community

Hypergear Highflow, Gtr Bov, Other Bits And Pieces

Yeedogga
 Share

Recommended Posts

Yeedogga Experienced

Yeedogga

Posted
Posted

Hi all,

Just throwing a few things up for sale. Will be updating/adding more over the next few months :)

1. Hypergear Highflow- $650 ono

One of Stao's PU Highflows which is a direct bolt- on turbo for RB25s. Looks totally stock when bolted up.

Utilises the stock compressor housing so that you can use your existing intercooler and intake piping.

Bolts up to standard/aftermarket dump pipes.

Stock water lines can be used with some minor bends/adjustment.

Comes with alloy intake pipe, braided oil feed line, stock compressor outlet elbow, dp gasket and oil drain fitting.

This turbo made 287rwkw on my R33 at 19psi. Tuned by Toshi with S15 480cc injectors, 3" exhaust and return-flow cooler!

It has served me very well, only upgrading to chase more power.

post-55684-14166278159715_thumb.jpg

post-55684-14166278444348_thumb.jpg

post-55684-14166278898909_thumb.jpg

2. GTR bov - $50 ono

Stock GTR bov. Speaks for itself. Larger diameter- flows more air!

3. Stock RB25 R33 turbo- $200 ono

Had less than 100,000km when removed. In good condition.

4. Suede steering wheel - $50 ono

Good condition, a little worn in some areas. Note: Not a genuine OMP

post-55684-14166281586849_thumb.jpg

5. Stock R33 ABS diff- $250 ono

Stock diff, not shimmed or messed around with. Was getting a bit loose when it was removed but could easily be shimmed to toughen it up again!

post-55684-14166282416561_thumb.jpg

Most items located in Dubbo NSW. But can arrange postage on items or can take them to Sydney next time I am down.

PM for any questions!

Kane_R32 Experienced

Kane_R32

Posted
Posted

If anyone buys the high flow and is looking to change the rear to an OP6, I will have one available as I'm going to use a 21U for a little more response. Great turbo otherwise.

Good luck with the sale

  • 2 weeks later...
Yeedogga Experienced

Yeedogga

Posted
  • Author
Posted

Adding this to the thread- 3" bellmouth dump pipe section.

I had to make a new dump pipe so I have this bit for sale.

Would be of benefit to anyone wanting to make their own downpipe (this is the hard bit to make!)

5-Bolt nissan flange. 3" mild steel.

$50 ono

Cheers

post-55684-0-44880300-1417830164_thumb.jpg

post-55684-0-27002300-1417830171_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
    • BOLGE
      R34 Plug Identification

      By BOLGE · Posted

      legend thanks mate !
    • fatz
      Neil's R33 Gts-t Build

      By fatz · Posted

      Skidz
×
×
  • Create New...