Jump to content
SAU Community

Recommended Posts

Hey guys I have some parts for sale from an engine setup we built for a customer.
Selling due to going for a bigger setup.
The setup below made 554kw at all 4 tyres in an R34 GTR on 33psi and was an absolute animal on the street.

All parts are located in Smithfield NSW and can be shipped anywhere in Aus.

Buyers are more than welcome to have any parts inspected by whoever they trust.

1. Nitto 2.7L Stroker kit.

Billet crank which has been durafinished
Nitto I beam rods

Nitto/JE forged pistons (87mm with upgraded pins)

Never had a bearing failure, perfect condition.

RRP with the durafinished crank is just over $7500

Selling for $5500 ono

2. RB26 race spec cylinder head.

1mm oversize Supertech valves inlet and exhaust

Supertech bronze guides

Tomei springs

Tomei offset retainers

Tomei buckets

Tomei cam cap studs

Kelford 270 degree 10.5mm lift cams

Very heavily ported

Welded and reshaped combustion chambers

The head was recently serviced by Advanced Performance Machining.

Shim clearances are immaculate, sounds beautiful.

The replacement value of this cylinder head is around the 10K mark.

Selling for $6500 ono

3. Precision 6766 turbo setup to suit RB26

Precision 6766 ball bearing T3 turbine housing with V-band outlet and SP comp cover.

Powertune steam pipe turbo manifold

45mm Turbosmart gate

3.5" dump pipe

Screamer pipe and plumb back pipe (if you want it to be engineer-able)

Oil lines

Intake pipe and hot side intercooler pipe.

All exhaust parts ceramic coated

Asking $4000

Link to comment
https://www.sau.com.au/forums/topic/452825-fs-big-hp-rb26-parts/
Share on other sites

  • 1 month later...

Hey mate stroker kits at the machine shop now was going to keep itbto many time wasters also bought brand new pistons and pins if you want it price is $5300 any questions contact me in 0407498155

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...