Jump to content
SAU Community

Recommended Posts

Hello

The time has come for me to replace the coilpacks on the 25de. I'm not keen on spending big bucks on genuine ones and the aftermarket are still quite a bit.

I'm curious if a waste spark system would work well on a stock 25de as that's my cheapest option. Obviously the car is still on stock ECU and the dwell time won't change, what happens to the spark in this situation? Is this a route I could go down?

The car will see track days and a turbo at some stage.

Just after some advice, cheers

Link to comment
https://www.sau.com.au/forums/topic/454557-coilpack-replacement/
Share on other sites

If you can't change the dwell through some aftermarket ECU solution, then best to stick with a stock replacement. OEM, splitfire, whatever.

I assume youre looking at ECUs if you're turbocharging the vehicle? If so then you could try an LS2 coilpack conversion. Even then splitfires make an easy drop in solution, depending on how much boost you want to run.

In my neo with less than 15 psi boost and ls coils they were fine at stock dwell . sorting the dwell fixed the spark issue at higher boost.

For an na Ls coils will be fine on stock boost. (Get it. No boost. Whatever, stock dwell and stock boost is fine, therefore stock dwell and no boost won't misfire ,)

Correct me if I'm wrong, but you can't have a waste spark ignition on a stock ECU. The ECU fires the spark, and it fires them one at a time, not in pairs.

You are wrong. It can be done. It's not the best option though. There's a guide somewhere in the net.

Thanks for replies guys, I was afraid I'd have to fork out big but looks like Splifires it is.

I'm not changing ECU until I turbo the car which is down the line.

The issue with wasted spark on stock is not the firing signal (just a matter of wiring the pairs), but the dwell time. Would the spark be weaker by about half as it's proving spark for two cylinders?

What kind of "wasted spark" are you talking about? If you have a single ignition output driving 2 coilpacks, like OEM or splitfires, then there is no degradation of the spark, it simply means that each coilpack is firing twice as often (one spark being "wasted" on the exhaust stroke)

One caveat would seem to be the difference in duty cycle between wasted and fully sequential ignition, especially when you start increasing dwell. Then there could be an argument about additional heat and the negative effects on the coil.

I run splitfires in wasted spark configuration, with 2ms of dwell. Although its perfectly fine on 13psi of boost, longevity of the coils is something on my mind. (hence keeping the dwell time down)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
    • I've got MCA Blues on my V36 Skyline, and while I've managed to sort out issues with scrubbing/bottoming out by raising it a smidge and increasing the damping hardness, the rear end still sounds *super* noisy when driving on anything other than the flattest surface imaginable. It sounds like a small party of flamingos are just chatting away in the back, which makes me think there are several link points in the suspension contributing to the noise. Am I hearing dried out/worn bushings? None of it sounds like metal-on-metal, it sounds more like hard rubber squeaking on metal. It's been suggested that a bit of silicon spray on each bushing might quiet them down, but I'm not sure what material the current bushings are made of (probably factory, I imagine) and whether silicon spray will degrade that material.
    • The obvious answer here is get a ND2/3 RF with the Targa top. The red is nicer, too!
×
×
  • Create New...