Jump to content
SAU Community

Fs: Potenza Re01r 235/45/17

angel13th
 Share

Recommended Posts

GH05T Grand Master

GH05T

Posted
Posted (edited)

spaz moment, the 235/40 compared to the 45, this will increase spedo reading yes?

i know only by likr 3-4% but i have a 10% speedo error (always reading to high) anyway

Edited by GH05T
Birds Grand Master

Birds

Posted
Posted

The higher profile will make the car go faster than the speedo is reading, so if your speedo currently reads higher than you're actually doing, it will correct this somewhat...but rather negligible as you say.

Birds Grand Master

Birds

Posted
Posted

Let's not use confusing terms that could be interpreted differently.

Speedo runs off the gearbox output shaft, so it takes its reading based solely on engine rpm and the gear selected, irrespective of what's happening at the tyres and diff. Therefore, 2000rpm in 5th will always make the speedo read the same speed (say ~80km/h) no matter what size tyres or diff ratio you have.

Increase your tyre diameter and the vehicle physically goes faster but the speedo reading stays the same. So if your speedo reads high, putting on larger tyres will make it more accurate. If it reads low, putting on larger tyres will make it more inaccurate.

Birds Grand Master

Birds

Posted
Posted

Manufacturers usually calibrate the speedo to the standard tyre diameter and make it read a little bit high so that they aren't responsible for people's speeding fines.

  • 2 weeks later...
  • 2 weeks later...
GH05T Grand Master

GH05T

Posted
Posted (edited)

received the tires, unfortunately i stuffed up the tire speed calculation (yep did it backwards in my head....derp).
my speedo error reads to high already, the new diameter for my wheels means it will now read higher again not lower so they really dont suit which sucks.

still unfitted
which sucks cos the tread pattern looks so nice

re listed in sa :P

http://www.sau.com.au/forums/index.php?app=forums&module=post&section=post&do=new_post&f=12


Edited by GH05T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...