Jump to content
SAU Community

Wiring Diagram for a Z32 AFM?

wannabe

By wannabe,
in Engines & Forced Induction

 Share

Recommended Posts

wannabe Proficient

wannabe

Posted
Posted

Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Link to comment
https://www.sau.com.au/forums/topic/45501-wiring-diagram-for-a-z32-afm/
Share on other sites
R31 POWER Mentor

R31 POWER

Posted
Posted

I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V

2 = AFM ground

3 = AFM signal

OMRAN Collaborator

OMRAN

Posted
Posted

hey mate ...

z32 MAF marked A to F but only four connections are used when fitting to the rb20det i think also rb25det (not sure )

A: Blank off

B: connect to Black wire

C: connect to black/silver

D: connect to white

E: connect to black with white trace

F: Blank off

you'll need the eprom remapped to suit

check out the pic

and good luck ... happy HP :D

  • 3 months later...
Trust33 Grand Master

Trust33

Posted
Posted
I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>  

1 2 3 4 5 6  

1 = no connect  

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect  

====ECR33 Flow===>  

1 2 3  

1 = 12V  

2 = AFM ground  

3 = AFM signal

Hi,Got to dig up an old thread

Does this mean that for the r33 all that is needed to do is to ground the z32 afm straight to the chassie.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal .... 3 on r33

3 = ground ..........straight to chassie

4 = AFM ground... 2 on r33

5 = 12V ...............1 on r33

6 = no connect

Targa Tom Proficient

Targa Tom

Posted
Posted
Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Gently remove lid, unsolder three pins, remove socket, do same to old AFM, fit socket, replace lid. Sika-Flex for seal.... Done.

TT

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Targa Tom Proficient

Targa Tom

Posted
Posted
And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>                      

1 2 3 4 5 6  

1 = no connect                                              

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect

====ECR33 Flow===>  

1 2 3  

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:D :wassup:

Make that unsolder "4"

:Oops:

Targa Tom Proficient

Targa Tom

Posted
Posted
weird why is that.And why would meggala say that it needs 4 wires to hook up.:D

I dunno, but I like to investigate alternatives, and for me it is easier to change the socket, and leave the loom in tact. Some prefer to solder wires and use heatshrink.

My method takes ten minutes from go to whoa... Each to their own.

Thats the beauty of having alternatives...

Anyone who is interested I have some pics zipped.

TT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...