Jump to content
SAU Community

Wiring Diagram for a Z32 AFM?

wannabe

By wannabe,
in Engines & Forced Induction

 Share

Recommended Posts

wannabe Proficient

wannabe

Posted
Posted

Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Link to comment
https://www.sau.com.au/forums/topic/45501-wiring-diagram-for-a-z32-afm/
Share on other sites
R31 POWER Mentor

R31 POWER

Posted
Posted

I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V

2 = AFM ground

3 = AFM signal

OMRAN Collaborator

OMRAN

Posted
Posted

hey mate ...

z32 MAF marked A to F but only four connections are used when fitting to the rb20det i think also rb25det (not sure )

A: Blank off

B: connect to Black wire

C: connect to black/silver

D: connect to white

E: connect to black with white trace

F: Blank off

you'll need the eprom remapped to suit

check out the pic

and good luck ... happy HP :D

  • 3 months later...
Trust33 Grand Master

Trust33

Posted
Posted
I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>  

1 2 3 4 5 6  

1 = no connect  

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect  

====ECR33 Flow===>  

1 2 3  

1 = 12V  

2 = AFM ground  

3 = AFM signal

Hi,Got to dig up an old thread

Does this mean that for the r33 all that is needed to do is to ground the z32 afm straight to the chassie.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal .... 3 on r33

3 = ground ..........straight to chassie

4 = AFM ground... 2 on r33

5 = 12V ...............1 on r33

6 = no connect

Targa Tom Proficient

Targa Tom

Posted
Posted
Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Gently remove lid, unsolder three pins, remove socket, do same to old AFM, fit socket, replace lid. Sika-Flex for seal.... Done.

TT

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Targa Tom Proficient

Targa Tom

Posted
Posted
And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>                      

1 2 3 4 5 6  

1 = no connect                                              

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect

====ECR33 Flow===>  

1 2 3  

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:D :wassup:

Make that unsolder "4"

:Oops:

Targa Tom Proficient

Targa Tom

Posted
Posted
weird why is that.And why would meggala say that it needs 4 wires to hook up.:D

I dunno, but I like to investigate alternatives, and for me it is easier to change the socket, and leave the loom in tact. Some prefer to solder wires and use heatshrink.

My method takes ten minutes from go to whoa... Each to their own.

Thats the beauty of having alternatives...

Anyone who is interested I have some pics zipped.

TT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Duncan
      What brakes on R34 GTT(Europe)

      By Duncan · Posted

      Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...