Jump to content
SAU Community

Recommended Posts

After reading this post about a journo snapping a drive shaft (and possibly more) after a spirited launch I'm wondering if any SAU members have had any issues like this?

zrqnod3jpftpmbeh5byv.png

Considering this would have been Nissans 'Journo Car' I'd be surprised if it hadn't already had a seriously tough life.

haha, good read! - Poor R35 probably gets the tits thrashed off it for "journalism purposes" lol!

Other than traction, nothing as of yet, I've split a red bull though, that was horrible - Going to miss the N/A reliability in that sense!

Edited by Jordy32

Iv been in a car that snapped the driveshaft (late 90's XR6).

You have no idea the racket that a driveshaft can make beating against the car and road at x000 rpm as the driver tries to get going but not knowing what was wrong (driveshaft had snapped near the diff so plenty of length to be crashing around).

When the car was repaired they said we had nearly beaten through the fuel lines too which would have ended pretty badly for everyone....

No issues here.

Must have been an unlikely failure.

I reckon yours (and most privately owned) have had much easier lives than those lived by Journo test vehicles. :D

Or, maybe not Snowy's.

I know that sound all too well.

yep. that's snapped good. what caused this? a launch?

my friend broke his doing drift on a grass field and then coming off onto the road (from a verge so the car jumped down onto the road) with the wheels still doing in the vicinity of 100+kmh and the car doing about 30.

What did the laws of physics and friction saw to the driveshaft?- SNAP!

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...