Jump to content
SAU Community

Recommended Posts

Hey, been looking for similar problems on the forum but wasn't too sure still.

Basically, my m35 stutters when driving slowly and turning tight, happened the first time when doing a U turn and since, when I am parking/reversing/...

I can take a video of the car doing it if you want to help explaining the problem.

I have an extra unrelated question. There is a small switch just behind the panel where the obd2 connector is, anyone would know what it is?

Thanks!

Hey, been looking for similar problems on the forum but wasn't too sure still.

Basically, my m35 stutters when driving slowly and turning tight, happened the first time when doing a U turn and since, when I am parking/reversing/...

I can take a video of the car doing it if you want to help explaining the problem.

I have an extra unrelated question. There is a small switch just behind the panel where the obd2 connector is, anyone would know what it is?

Thanks!

shudder could be because of the "tight corner phenomenon" and the 4wd system but thats just a guess. The switch sounds like it could be to turn on the attesa pump when u need to bleed the system

shudder could be because of the "tight corner phenomenon" and the 4wd system but thats just a guess. The switch sounds like it could be to turn on the attesa pump when u need to bleed the system

Ha! I've pressed that switch multiple times and not too sure in which position I left it :/

The shudder is quite intense once it starts, is there a way to easily turn off the 4WD to validate that ?

Ha! I've pressed that switch multiple times and not too sure in which position I left it :/

The shudder is quite intense once it starts, is there a way to easily turn off the 4WD to validate that ?

All this is just speculation tho, my car has the shudder at full lock too ;). I guess for the switch you could flick it on and off and listen for your pump under the back right hand side of your car while your car is off. if the pump don't turn on then its not the switch lol

Ha! I've pressed that switch multiple times and not too sure in which position I left it :/

The shudder is quite intense once it starts, is there a way to easily turn off the 4WD to validate that ?

No there isn't an easy or safe way. These have a different Awd system to the c34. It is not good for the transfer case. The only way to properly make it rear wheel drive is to pull the front drive shaft

Took the car for a ride and couldn't get it to shudder again so no video yet of it..

For the switch, I tried to follow the cables ( red and black+red) and they go up in the ride side of the steering wheel in the dash.

Maybe it's related to the alarm or something. The car also has this little remote to start it from outside (which doesn't work).

The switch is definitely not stock as it was fitted with screws in two holes in the lower dash just above the pedals. Can't see any light turning on/off when playing with it.

I never got the remote with my car. I just done some research to find out what the switch was for. Mine has a silver sticker above it with Japanese writing. Had it translated and yeah it is remote start

Ha! That's it then, got the same sticker so that's sorted out ! I'll get a video when the car shudders again and put it here, should help with the troubleshooting. Weird that it doesn't happen every time (maybe only when really hot, will have to test)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Nismo, any chance in the world you still have these seats?
    • I'd say closer to OG GTX3582R, just smaller trim - so 59mm inducer/82mm exducer as opposed to 62/82 for the first gen GTX3582R. Yeah EFRs were boss, the EFR8474 is still an absolute beast and it perplexes me that people still go to things like Turbosmart/Garrett etc when the results people are getting with those are pretty unremarkable compared to what you could get with a turbo available well before those options came out.  DriftSquid (I think) "upgraded" from an EFR9174 to a Turbosmart turbo and promised a comparison video - and kinda shuffled awkwardly and did a bit of diversion from the fact that they didn't get any improvement going to the currently massively hyped brand of turbo from a turbo that was a bit of a frankenstein that had been well superceded in it's own range before the Turbosmart unit he put on there even came out. I suspect the EFR would outperform most Xonas for what a lot of less-insane RB owners would go for, in the 400-600kw range but the Xonas are looking hard to beat up to maybe in the mid 700kw range at this stage- basically where EFRs don't really reach, and before the Precision turbos take over.  What the Xonas do well in the "EFR range" is be easier to package etc, and work very well if a divided housing doesn't suit your application.  
    • Are you sure the gasket is blown? What are the issues? Thermocure is the only flush I've seen do anything with rust, very impressed with that, Prestone, rust will be by the pool having a cigarette.  
    • And since the flush you have a blown head gasket? Have you lifted the head off yet?
    • The answer is to get a hold of the wiring diagram, work out what voltage is supposed to be where, when, and then work out why it is not there, then. I can't speak to the HR34 stuff, because I have never paid any attention to the NAs. There is a possibility that the turbo diagram will help, but it could also be different - depending on whether there is an FPCM on the NAs.
×
×
  • Create New...