Jump to content
SAU Community

Recommended Posts

Hey, been looking for similar problems on the forum but wasn't too sure still.

Basically, my m35 stutters when driving slowly and turning tight, happened the first time when doing a U turn and since, when I am parking/reversing/...

I can take a video of the car doing it if you want to help explaining the problem.

I have an extra unrelated question. There is a small switch just behind the panel where the obd2 connector is, anyone would know what it is?

Thanks!

Hey, been looking for similar problems on the forum but wasn't too sure still.

Basically, my m35 stutters when driving slowly and turning tight, happened the first time when doing a U turn and since, when I am parking/reversing/...

I can take a video of the car doing it if you want to help explaining the problem.

I have an extra unrelated question. There is a small switch just behind the panel where the obd2 connector is, anyone would know what it is?

Thanks!

shudder could be because of the "tight corner phenomenon" and the 4wd system but thats just a guess. The switch sounds like it could be to turn on the attesa pump when u need to bleed the system

shudder could be because of the "tight corner phenomenon" and the 4wd system but thats just a guess. The switch sounds like it could be to turn on the attesa pump when u need to bleed the system

Ha! I've pressed that switch multiple times and not too sure in which position I left it :/

The shudder is quite intense once it starts, is there a way to easily turn off the 4WD to validate that ?

Ha! I've pressed that switch multiple times and not too sure in which position I left it :/

The shudder is quite intense once it starts, is there a way to easily turn off the 4WD to validate that ?

All this is just speculation tho, my car has the shudder at full lock too ;). I guess for the switch you could flick it on and off and listen for your pump under the back right hand side of your car while your car is off. if the pump don't turn on then its not the switch lol

Ha! I've pressed that switch multiple times and not too sure in which position I left it :/

The shudder is quite intense once it starts, is there a way to easily turn off the 4WD to validate that ?

No there isn't an easy or safe way. These have a different Awd system to the c34. It is not good for the transfer case. The only way to properly make it rear wheel drive is to pull the front drive shaft

Took the car for a ride and couldn't get it to shudder again so no video yet of it..

For the switch, I tried to follow the cables ( red and black+red) and they go up in the ride side of the steering wheel in the dash.

Maybe it's related to the alarm or something. The car also has this little remote to start it from outside (which doesn't work).

The switch is definitely not stock as it was fitted with screws in two holes in the lower dash just above the pedals. Can't see any light turning on/off when playing with it.

I never got the remote with my car. I just done some research to find out what the switch was for. Mine has a silver sticker above it with Japanese writing. Had it translated and yeah it is remote start

Ha! That's it then, got the same sticker so that's sorted out ! I'll get a video when the car shudders again and put it here, should help with the troubleshooting. Weird that it doesn't happen every time (maybe only when really hot, will have to test)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...