Jump to content
SAU Community

Recommended Posts

Just spoke to a friend of mine who had his 100,000 k service done today. He was lucky to have driven 15kms and his engine siezed.

He first noticed a loud clunking/ticking/rattle from the engine that he describes as a metal on metal sound. Now the engine will not even tick over.

The maintenance he had done was:

Timing belt changed

Tension pulley tightened (due to belts screaching on startup)

Several seals replaced (ie, crank seal)

fuel filter changed

oil / oil filter change

One thing that sounded a bit dodgy was a crank bolt which he ( the mechanic) apparently snapped and had to replace.

We are going to confront the mechanic tomorrow and want to make sure we know we know what is wrong first so the guy cant feed us any bulls%*t.

I think the most likely cause is the timing belt not fitted correctly.

What do u guys think and how can we confirm that this is the problem?

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/
Share on other sites

if your motor wont turn over means your engine is ****ED. happend to me on my 300zx, after it siezed up had to rebuild the motor. good luck and please dont be shy to confront the mechanic and make him pay for the rebuild.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936789
Share on other sites

Whatever happened clear case of mechanical screw up on their behalf. I don't quite know how they'd try and wrangle out of it.

but if they do try, get an independent inspection ASAP (like today) by another party or two, get it in writing.

And if you need to take legal action against the mechanic involved, this will help.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936965
Share on other sites

I'm thinking out loud here, but goig back about ~11 years ago I had a suzuki swift gti, going in for a timing belt/cam belt change. Apparantley the pulley needed to be put on a special way which the mechanic did not do.. we drove about 80k's, and when we tried to restart the car, it would not start... Thankfully it didn't blow the motor, but was an expensive tow from Bells Beach to Melbourne, ended up taking the matter to the Small Claims tribunal and won.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936968
Share on other sites

Yeah the oil was checked and even replaced after my friend told the mechanic the car is making a noise. The mechanic said just to put a thicker oil in it and it will be fine. Then 10 km later bye bye engine.

The car is getting towed to the mechanic now and the dick still thinks its the oil.

I dont think he has a clue.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936981
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
    • Yeah, I would have said the same. It makes me suggest that there are other things wrong, such that the ECU is totally unhappy with the broken sensor. The only other thought here is that maybe it is shorted, which might cause a different issue to the typical "disconnected" sensor.
×
×
  • Create New...