Jump to content
SAU Community

Recommended Posts

98 c34 stagea rs4s factory manual

Looking for $8000

Located Inverell

205,000 km

Hypergear hiflow

Adaptronic plugin needs to be tuned

600 cc injectors

Npc clutch

Towbar

Pwr intercooler

Walbro 255l fuel pump

Tien coilovers

Bad points

Unregistered

Needs new front bar and guard fixing

Rust under mirrors

4wd light comes on

Paint on the wing is peeling the rest is pretty good it's been resprayed at some point

This was my daily so it's not perfect I have owned it since 170,00 km it's been reliable I have most parts needed for rego I just haven't fitted them I can if needed there's a few spare parts and I have a 3 inch dump pipe it won't come with the 18s there cracked and I will put new tyres on the 17s on the front. post-83554-14536251821225_thumb.jpgpost-83554-14536252039003_thumb.jpgthere's probably more that I have missed. Only reason I'm selling is I don't have the time or money and have lost interest and getting in the road.

post-83554-14536250636494_thumb.jpgpost-83554-14536250832819_thumb.jpgpost-83554-14536250995671_thumb.jpgpost-83554-14536251138223_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/462462-nsw-98-c34-stagea-rs4s-8000/
Share on other sites

  • 4 weeks later...
  • 2 weeks later...

When I was driving it I was running same size wheels and the issue has always been there I only have the silver wheel on because the rim was cracked and repaired but still leaks. Thanks for the suggestion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...