Jump to content
SAU Community

Problem: Clunk When Cornering/take Off/stop - Solution!

SandalsBoy
 Share

Recommended Posts

SandalsBoy Enthusiast

SandalsBoy

Posted
Posted

Just thought Id post the fix to a really strange problem that my car had just in case someone else encounters the same thing... i cant explain it... but it worked. Please excuse my poor technical knowledge. If every

Car: '89 R32 GTR

Problem: When cornering, taking off, or coming to a stop, there would be a solid clunk / thud.

Fix: Replaced clutch pivot ball and clutch

Long version of the story: I was sure it was a suspension problem. However all the bushes, shocks etc checked out ok. Then one day whilst driving, my clutch friction point dropped almost to the floor, clutch would still disengage... but only just. This prompted me to get this (what I thought was an unrelated problem) looked at.

Took the car to the mechanics and it turns out that the clutch fork pivot ball had snapped off. They rigged up some sort of replacement using a bolt of some sort, and replaced the old worn out button clutch with a simple heavy duty item.

To my suprise, when I got the car back, there was no more clunking noise! I cant explain this as the "clunk" didnt correspond to the depression of the clutch.

Hope this helps someone.

Jono.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...