Jump to content
SAU Community

Recommended Posts

Hey mates,

i want to sell my Nissan Stagea RS Four

 

Basics:

Nissan Stagea S1 RS Four

First Registration JP 12/1996

First Registration UK 01/2008

First Registration Germany 06/2015

90000km (no miles !)

Automatic

 

Mods:

R32 GTR Brakes (Non V-Spec)

R33 GTR Rims

Custom 3" Exhaust

Front mounted intercooler

Tein Suspension

 

All fluids have been changed. Timing Belt was changed 2 weeks ago. The car was painted in 02/2016 because of rust under the wing mirrors. (Front fender, front door, rear door, on both sides)

Underbody is clean !

 

I have a lot of pics and also a video.

Export is no Problem.

 

Price for the car AU$13000

 

For pics and information please contact me on whatsapp.

+49 176 83251050

IMG_20160703_185809_744.JPG

IMG_20160701_192700_499.JPG

IMG_20160701_165604.jpg

IMG_20160610_084346_213.jpg

IMG_20160602_175255.jpg

Link to comment
https://www.sau.com.au/forums/topic/465606-nissan-stagea-s1-rs-four/
Share on other sites

Yes. The car is located in germany.

 

There was a bit of rust on the underbody. I removed the rust, used rust converter and sealed it with underbody protection.

 

I have a lot of pics so that the possible buyer can see, i dont only oversprayed the rust.

 

Here is what it looked like before.

IMG_20160625_113655.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...