Jump to content
SAU Community

Paintless dent removal - Dent Garage - Macquarie Shopping Centre *RECOMMENDED*

BunsenBurna

By BunsenBurna,
in New South Wales

 Share

Recommended Posts

BunsenBurna Proficient

BunsenBurna

Posted
Posted

Paintless dent removal - Dent Garage - Macquarie Shopping Centre *RECOMMENDED*

Hi all

Yesterday I had a couple of tricky golf ball size dents removed from the rear of my 1986 FC RX7 and I am delighted with the workmanship.

Simon Booth runs Dent Garage www.dentgarage.com.au out of Macquarie Shopping Centre - the quality of his work is high, price was reasonable and he's a lovely bloke. He was one of the first guys in the country 25 odd years ago to get into and master this craft.

Highly recommended!

Rx7 PDR Dent Garage Before and After-1.jpg

Scott

  • Like 1
Link to comment
Share on other sites
InfinitiG35 Contributor

InfinitiG35

Posted
Posted
Paintless dent removal - Dent Garage - Macquarie Shopping Centre *RECOMMENDED* Hi all
Yesterday I had a couple of tricky golf ball size dents removed from the rear of my 1986 FC RX7 and I am delighted with the workmanship.
Simon Booth runs Dent Garage www.dentgarage.com.au out of Macquarie Shopping Centre - the quality of his work is high, price was reasonable and he's a lovely bloke. He was one of the first guys in the country 25 odd years ago to get into and master this craft.
Highly recommended!
Rx7 PDR Dent Garage Before and After-1.jpg
Scott


How much did it cost you? I have about 3-4 golf size dent in my car as well.
Link to comment
Share on other sites
BunsenBurna Proficient

BunsenBurna

Posted
  • Author
Posted
1 hour ago, InfinitiG35 said:

How much did it cost you? I have about 3-4 golf size dent in my car as well.

$250 which was the same as a quote I got a while back from a mobile guy.

I should point out that Simon found a very minor third dent just above the top one in the pictures which he smoothed out as part of the process. Also, that top ding circled in the picture needed more attention because it was on an edge.

It took just less than 2 hours. He can give you a quote on the spot and you can book it in from there.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Sleepergm
      Max horse power stock internals?

      By Sleepergm · Posted

      And yes would be going to tomei Japan for sure as it’s closer to me … 
    • Sleepergm
      Max horse power stock internals?

      By Sleepergm · Posted

      Yeah I heard the same. Might be hard to order one. But then I guess can go to hks or go to a more expensive n1 block with tomei. Guess will jump the hurdle once I get there next upgrade around. I can’t get work done in the states as the lead time will take for ever on top of shipping to Hong Kong. 
    • joshuaho96
      Max horse power stock internals?

      By joshuaho96 · Posted

      https://www.platinumracingproducts.com/en-us/products/nissan-rb26-cast-blocks This is the solution I was thinking of. I would stay away from Tomei USA, their quality is a question mark to me. If you want an engine machined in the US contact Club DSPORT: https://clubdsport.com/ Tomei JP is probably fine but I recall they stopped doing pre-assembled short or long blocks. In general it's pretty tough to get any kind of RB26 block at the moment with Nissan so severely backordered.
    • joshuaho96
      Nismo front and back LSD

      By joshuaho96 · Posted

      PAR specifically offers stock ratios in their gearset and you could do whatever ratios are physically possible supposedly for no extra cost. I agree 6 ratios is better than 5, the factory 2nd gear is equivalent to the Getrag 2nd gear if you account for the differing final drive ratio though. The Getrag 3rd gear with a 3.916 final drive is equivalent to a 1.6 2nd gear in the FS5R30A. I'm about to swap the transmission out on my car, I'm tempted to send the one I have now out for rebuild with the standard "cross ratio" gearsets out there to see if it really makes such a big difference the next time I pull the transmission.
    • Sleepergm
      Max horse power stock internals?

      By Sleepergm · Posted

      This is what I was looking at next:  https://www.z1motorsports.com/engines/tomei/tomei-rb26-28l-short-block-assemblies-p-45479.html as we can’t bore the cylinders out in hk so better just buy the whole lot in one and install then retune. Everyone saying the weak link are the bolts holding the rods together. I already did valve springs, arp head bolts, hks racing coils, nismo fuel pumps and pressure regulators, injectors etc for the top of the engine. 
×
×
  • Create New...