Jump to content
SAU Community

Recommended Posts

Recaro seat refresh - places in Brisbane?

Hi guys,

my Recaro drivers' seat needs a refresh - foam has collapsed on the door side where you get in/out.

Any suggestions for Brisbane based companies that could restore my Recaro seat?

cheers

Mike 

On 7/9/2017 at 9:32 AM, Cadmoon said:

Also interested in upholstery recommendations. You might have more luck on the FB group as not many people frequent here unfortunately. 

Hi Cadmoon,

advice from the Melbourne based IdealSeat Company - agents for Recaro in Australia - is that they can supply replacement parts for Recaro seats (depending on model).

I sent them photos of my Recaro seat, and they replied that the replacement part for my seat (door side where you get in/out) was $90 plus delivery, and that any Motor Trimmer could fit it.

I've spoken to several Brisbane based motor trimmers since then with various responses - the best was, "if you remove the seat and provide the replacement foam it will cost $90 to replace it".

Approx $200 to fix is fine by me if it's done right - I'll let you know the outcome once it's done.

cheers

Mike

  • 5 months later...

Got the piece from Idealseat and had it fitted by Archerfield Auto and Marine Upholsterers

http://www.upholsterers-brisbane.com.au/

Cost $100 to fit, and $103 delivered for the piece from Idealseat.

Nice work - you can't tell it's not original.

I've no idea what a Recaro costs (mine came with my car) - but $203 for a good repair avoids more landfill.

cheers

Mike

  • Like 3
  • 2 weeks later...
On 12/22/2017 at 12:01 AM, PWND said:

Might check out Marine Upholsterers for an unrelated seat refurbishment. Always good to hear a positive review

they did good work for me and reasonably priced - I will go back there again for further work I need.

cheers

Mike

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...