Jump to content
SAU Community

Recommended Posts

 

Description from Scotty's customs:

 

When changing to an aftermarket fuel rail you used to require an aftermarket fuel regulator, but with this adapter that’s a thing of the past. Screws into most aftermarket fuel rails using an 8an thread with Oring.

 

Bought from scotty's customs for $80, will sell for $40 posted ONO.

 

New, never used. Went with an aftermarket fuel reg instead.

 

Located Melbourne

 

20170723_213456.jpg

 

Link to comment
https://www.sau.com.au/forums/topic/471345-parts-off-r33-gtst/
Share on other sites

Jasma 3 inch stainless steel diff back exhaust in excellent condition. No rust, holes or dents. Comes with hangers to suit an R33 gtst perfectly.

 

Reduces to 2.5 or 2.75 near the tip (can be seen in pics). I had this on my car with no other mufflers and it sounded great, had that deep, clear rb25 note and made the perfect level of noise. Fairly loud but never drew the wrong attention or made you deaf from drone.

The exhaust is angled.

 

Selling because i don't like the look of canon exhausts and got an oval muffler instead.

 

My car made 250rwkw fine with this exhaust. Might get restrictive once you get to 270-280 but im not an expert.

 

$150 ONO

 

20170723_221845.jpg20170723_222229.jpg20170723_222310.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...