Jump to content
SAU Community

Recommended Posts

M35 Starter motor

Hi all,

I thought I would recommend a repairer in Sydney after getting much more expensive repair quotes.

The starter motor died (complete failure) and wouldn't turn the engine over at all, even when tapped with a wrench. It wouldnt even make the ticking sound that they usually make when they die.

I was quoted between $120 and $200 for second hand starter motors from wreckers. New starter motors were upwards of $800 coming from overseas.

I decided to use the same repairer that I used for a previous m35 starter motor (different car). Both times cost $180. They use genuine parts for the hitachi unit and end up sounding and performing like brand new. The car now starts on first crank.

The repairer I used is:

Concord autoelectrical and mechanical repairs on Parramatta rd close to the start of m4.

 

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/472024-m35-starter-motor/
Share on other sites

  • 2 weeks later...

Niiice.

I just went through this myself. Ended up buying a battery because I thought it had dropped a cell since the car was struggling to turn over haha.

Found a few threads on here stating the same thing with the M35 so whipped the starter out and found it caked in crap due to worn brushes. 

There's brush kits available on eBay or even genuine Nissan (part number 23378-0M300) but mine still had a bit of meat left so just cleaned it all up.

I did have minor scoring on the armature but not enough to be concerned. Threw it back in and sounds/starts like a new one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...