Jump to content
SAU Community

Recommended Posts

I didn't find the Autronic that great.. but probably due to the support over here.

No one could get it to run with the GTR..

Here is an autronic running on a GTR... 391rwkw if i remember correctly? It was run in the Dutton Rally full 'o' stickers.

gallery_-_ourcustomers_-_slideshow12.jpg

gallery_-_ourcustomers_-_slideshow11.jpg

I had a look at some of the things they were doing with the ECU, and was pretty impressed. There is a switch in the cabin to turn on data logging, it monitors pretty much every possible part of the engines operation, has some sort of real time tune(??) and much more importantly, makes funky looking graphs to impress slack jawed yokels like me.

Yeah, its a track car so I guess its tuned for reliability?

Beats me, I'd like 390rwkw (which is especailly impressive when I have a FWD car)

Off topic for a second ... Have you heard of a link computer to suit the E5B6 computer as found in the jap-spec (and all over NZ) E5T from the ~1987 Mazda Familia GTX?

And off topic again ... Anyone know of any advantages of the HKS Fcon V over the PowerFC?

It seems that there is only one (1???) tuner in the whole of australia for the HKS Fcon V which on paper seems to have no advantages over the PowerFC, of which there are tuners on every street corner?

Great if you have Manual, but what if you have an Auto??

Anyone had experience with the TSI?

i have....very simple theory that it is based on however needs more R&D...little bugs exist in it...hence last time i heard there steering away from motorvehicles and turning to bikes :headspin:

hi guys, jus wondering wat would b a good computer 2 buy for my skyline r33 gtst? i dont have any knowledge on computers but hav mates that do but not on skylines. any help would b appreciated

it really comes down to budget....power fc are excellent value if u manage to skip customs through the internet orders.....tuning wise there are probably three ppl in sydney that i would use to tune this ie. CRD (~$800) via laptop , Unigroup via handcontroller (~$450), Hitman via laptop ($300 flat rate)

it comes down to what do u expect out of car or intend to do with it.....if u are going for more than 300rwkw than i would think long and hard bout the choice of comp as an understanding needs to established between u and the tuner....its always nice as the computer is only as good as the tuner :D

i personally run a Haltech on my rb25 which runs as a plug-in and is done by JEM over at moorebank....adam there does also EMS, MICROTECH, TSI, MOTEC....HITMAN actually works there also from under the same roof so pretty much whatever computer ur running something can be done about it....however its only a RWD dyno hence GTR ownrs are at a disadvantage........ :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...