Jump to content
SAU Community

eManage Ultimate package w/ WB O2

Cruiser Al
 Share

Recommended Posts

Cruiser Al Rookie

Cruiser Al

Posted
Posted
Trust Greddy eManage Ultimate package!
 
Comes with a harness which I’m guessing is a universal, has been used previously as evident by the wire tips being soldered!
Also comes with..
- MAP sensor.
- Innovate motorsports wideband o2 controller and all wiring to connect to serial port.
- Bosch wideband o2 sensor with weld in bung
 
Happy to post etc

emanage 2.jpg

emanage 1.jpg

loom.jpg

innovate WB o2 controller.jpg

MAP sensor.jpg

innovate serial cable.jpg

innovate o2 sensor cable.jpg

bosch o2 sensor with bung.jpg

Link to comment
https://www.sau.com.au/forums/topic/479223-emanage-ultimate-package-w-wb-o2/
Share on other sites
  • 2 weeks later...
  • 5 weeks later...
  • 2 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Perhaps the answer is... more jacks!* *proper jacks must be used.  
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      I NEVER think about using a scissor jack unless there is absolutely no other alternative. f**king things are dangerous, annoying and stupid.
    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
×
×
  • Create New...