Jump to content
SAU Community

R34 starts then stalls instantly

tdavi280
 Share

Recommended Posts

tdavi280 Newbie

tdavi280

Posted
Posted (edited)

I've just put a rb25det neo into my r34. Motor was imported from japan. It is a factory manual n/a shell. I have a z32 afm, front mount intercooler, gcg hi flow turbo. ECU is a PowerFC. Still running factory injectors and the standard fuel pump. I have a walbro 460 and bosch 1000cc injectors ready to go, putting this in before my tune then getting the car towed to my tuner.

Now to my issue, I try to start the car and it runs for about a second then stalls straight away. If I continue to hold the key to keep it cranking it will run until I back it off then it stalls. 

So far I have tried swapping the fuel lines that join from filter to rail and regulator etc. I swap them and then car just cranks and doesnt fire so assuming I have lined around the right way. I put in a fresh 10L of fuel to rule out not having enough fuel. Also keeping in mind that the car ran fine with its n/a motor barely a week ago so doubt fuel pump is toast. Still can hear fuel pump priming before starting. Got a spare CAS and spun it out of the car while key was in ON position to check for injector pulse and all seems fine.

 

My tuner has said he'll obviously fix it but at $200p.h I'd prefer to get it running well before I drop it off.

 

Any help would be appreciated.

Edited by tdavi280
Link to comment
https://www.sau.com.au/forums/topic/479544-r34-starts-then-stalls-instantly/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
    • Duncan
      R33 GTR running -9 with no tune

      By Duncan · Posted

      Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Duncan
      Coolant leak?

      By Duncan · Posted

      Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
×
×
  • Create New...