Jump to content
SAU Community

Recommended Posts

I took my Skyza out to a wet pan event and whilst waiting my turn my car just died. I Jumped it and my voltage was just over 12. Keeping the revs up I was able to keep the car running. But voltage was still quite low. Then all of a sudden 13.8 for a bit then back down. It kept going up and down my whole trip home.

does this sound like a dodgy Alternator?

Link to comment
https://www.sau.com.au/forums/topic/484767-rb25-charging-issues/
Share on other sites

On 27/6/2023 at 8:56 AM, GTSBoy said:

And let's not bother finding out what is actually wrong.

Hey mate, I think the problem is actually the alternator light. I don't Chet the charge light coming on at all. Here is where it is currently plugged in to. Perils of picking up someone else's project. In the pic the circled bit is where the light wire is going. It is a white/red wire on the other side

 

IMG_4698.jpeg

IMG_4697.jpeg

On 30/6/2023 at 5:54 PM, GTSBoy said:

Yuh, so break out the multimeter and check the wiring. Pull the dash out and check the globe locally.

Ok, I have pulled the cluster out. The bulb is fine. There is power at both sides of the globe.

does this mean the Alternator is not earthing the wire when the ignition is on but car not running?

does this tell you anything?

5 hours ago, OO Dan OO said:

There is power at both sides of the globe.

If you have power both sides, then yes, there is no earth. That wire runs through the alternator as the exciter, which causes it to start producing current, which it will not reliably do without the excitation. You can follow it on the wiring diagram to see where it goes.

1 hour ago, GTSBoy said:

If you have power both sides, then yes, there is no earth. That wire runs through the alternator as the exciter, which causes it to start producing current, which it will not reliably do without the excitation. You can follow it on the wiring diagram to see where it goes.

I noticed there is no earth wire bolted to the back of the alternator. I clipped my test light on this bolt and tested a live wire to see if it is grounded and I got sparks. Does this mean my alternator is possibly just not grounding enough?

1 hour ago, OO Dan OO said:

I noticed there is no earth wire bolted to the back of the alternator. I clipped my test light on this bolt and tested a live wire to see if it is grounded and I got sparks. Does this mean my alternator is possibly just not grounding enough?

Impossible to say.

Get the wiring diagram. Make sure you have the same wiring as the diagram. If you have the same wiring, and it has continuity where it should, AND shit's not working.....then you suspect the alternator has a fault.

Just don't mistake the main power stud with a grounding point, there are a few different model alternators on these, but AFAIK they all have an M6 stud for the positive and an m5 bolt or stud for the earth. 

It does need to be earthed to charge properly

45 minutes ago, Duncan said:

Just don't mistake the main power stud with a grounding point, there are a few different model alternators on these, but AFAIK they all have an M6 stud for the positive and an m5 bolt or stud for the earth. 

It does need to be earthed to charge properly

It is a little bolt that I am talking about. Definitely not a stud. It doesn't have power just not earthed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...