Jump to content
SAU Community

Odometer LCD is Intermittently Wonky

Kip

By Kip,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Kip Contributor

Kip

Posted
Posted

Hi all,

For my '98 260rs...

The odometer LCD occasionally turns blank or gives me only the bottom half or top half of the numbers. It's intermittent, which leaves me to believe it's a dead solder or loose wire somewhere. The odometer itself works. When the screen comes back, kms have been added to the trip and overall meters. A couple questions:

  1. Is this a known issue with the Stagea? I didn't see it pop up in my quick search, but that could be my searching skills.
  2. How accessible is the LCD screen in the cluster? I'm hoping it's a remove and replace type situation versus cracking open the whole housing.

I'm hoping you all can narrow some of my initial troubleshooting. Any experience or opinions would be helpful.

 

Duncan Grand Master

Duncan

Posted
Posted

Hi mate, I have never had an issue with the odometer in mine (450,000+ klm now) and can't remember another post about it. Still, your description of the likely cause sounds spot on, so an electrics repair is probably the next stop.

Kip Contributor

Kip

Posted
  • Author
Posted (edited)
1 hour ago, Duncan said:

Hi mate, I have never had an issue with the odometer in mine (450,000+ klm now) and can't remember another post about it. Still, your description of the likely cause sounds spot on, so an electrics repair is probably the next stop.

Yay. I'm the lucky one who got the bad LCD. Only 138,000km or so on this car.  🙄

On a non-Nissan car I have, similar issues were related to failing cold solder joints. At least with the Stag, I'm not losing my speedometer, odometer, gas gauge, and temp gauge. I guess I get to go into the dash at some point. I'm not overly concerned about it, but it's annoying. Seems to be happening more frequently in the past couple weeks too. Not sure if that's the summer heat causing hassles or the problem genuinely getting worse. Bleh.

Edited by Kip
corrected typos

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      f**king around with the bro
    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      Ludenham   44.2 tops day no issues  
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Then today, I went to visit a man with an r33 hat Peter and Road and Race sorted the alignment. As it is being set up for general track/hillclimbs etc it has a heap of caster (7o), less camber than I am used to (1o front and 2o rear, as the caster looks after that in turns without the braking downsides), 3mm front toe out and 0 toe rear. Will see how that goes and track tyre wear to see if it does need more camber, but adjsustment is also limited with nismo arms and adjustable bushes at only 1 end. It does have a bent inner tie rod on the driver's side front but as it came up within spec I'll just leave that as is. So, that is getting close to my chapter of this story....could of tidy ups then a shakedown in early October before it finds a new home.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
    • Duncan
      Slight brake pedal stutter after new pads

      By Duncan · Posted

      what sort of caliper are they? If they are a slider and you gave everything a good clean, you might need to regrease the pins. My guess though is they will come good after some abuse as suggested above
×
×
  • Create New...