Jump to content
SAU Community

Recommended Posts

hey guys i posted this in general but havnt got a reply as yet, and i need to find out ASAP.

they are R33 superlow king springs, from a GTR and i need to put them n my GTST.

so can anyone tell me? i want to get them sent over b4 the photoshoot. so i really need to know.

thanks again guys.

Andrew.

ok called around and yes they will fit!!! however apparently im going to need some shocks for them , something along the lines of GTR ones.

anyone know if i do need new shocks or will mine do the job?

apparently the shocks will start to leak really badly if i use the stock ones?

If you put superlow springs in with standard shocks, your ride quality will be ruined, the car may bounce all over the place and it will wear out the stock shockers very quickly, (if they arent dead already) you may want to put some short throw shocks in at the same time to get some suspenson travel back. for example i put K-Mac 2.5 inch lowered springs in mine with the standard shocks, and the car would bounce all over the road, put some Koni Yellows in fixed it all up.

thanks mate, how much did the konis set you back?

i'll probably wait a little while to buy the shocks as i dont need to put the springs on immediatly.

one of the mech's at F&F said he put gtr shocks on with his lowered springs on his gtst, and that the ride is really stiff, but that wont bother me, im hoping at the end the car handles better too.

Remember the cost of compensating the camber if you're lowering too, or you'll scrub the inside of your tires with too much negative.

I'm in at Inline Steering & Suspension in Qbyn next week to finally sort out my camber issues once and for all, and with a few hours of labour it aint cheap.

(I have fairly low and $#&% hard TEIN coilovers)

thanks mate, how much did the konis set you back?

i'll probably wait a little while to buy the shocks as i dont need to put the springs on immediatly.

one of the mech's at F&F said he put gtr shocks on with his lowered springs on his gtst, and that the ride is really stiff, but that wont bother me, im hoping at the end the car handles better too.

they set me back around 1200, theyre customised in some way, i forget which, as the gts and gtr shocks have different heights and where they bolt on at the bottom (on a 32).

yeah well the only reason i got the springs is because they were so cheap. ($70 in perfect condition) so spending $1200 is outta the question.

im sure there is a more cost effective way, but in the mean time i guess they will be sitting at home casue i dont want a sloppy ride with leaking shocks.

yeah im not really worried about the ride feel.

i just dont want to harm the shocks or any other parts of the suspension, if there wont be any damage to the shocks then i'll put them on b4 the photoshoot.

yeah isnt to hard, i'll take you up on that offer though, if they come in the next few days maybe you have some spare time help put them on? i dont think it will do any harm if they are on for a few weeks?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...