Jump to content
SAU Community

Recommended Posts

It time to get some new rubber on the beast.

At the moment Im running 225*45*17 all round.

(I think the wheel size is 17*7.5jj)

For some weird reason I suffer from a lack of traction at times...

Anyone got any recommendations on what size tyres to put on?

Would 245*40*17 all round be a decent choice?

or prehaps 245*40 at the rear and 225*45 at the front?

Or am I just better sticking with 225*45 all round?

Link to comment
https://www.sau.com.au/forums/topic/50735-tyre-size-recommendation-for-r34gtt/
Share on other sites

I'd be very careful. Changes to the rolling diameter can affect the TCS adversely and think its constantly slipping. Now of course if you drive with it off its doesn't matter.

Thanks for that.

According to the book at the tyre dealer the difference in diameter between both sizes is 4mm. You get more difference than that between a new and worn tyre so it should be ok I guess.

Why wouldn't you put the widest tyres you can fit and afford?

You might have different width if your rear guards can hold wider than your front ones as they do on a GTT but with 7.5" wide rims you're not where near too wide so put the widest sensibly possible on there.

Why wouldn't you put the widest tyres you can fit and afford?

 

You might have different width if your rear guards can hold wider than your front ones as they do on a GTT but with 7.5" wide rims you're not where near too wide so put the widest sensibly possible on there.

Ok, thanks.

That makes sense.

I assume that 245 is as wide as I should go on 7.5" rims?

Is there any particular reson to put the same width on front and back?

Ive seen a number of cars which are different from front to rear.

yeah the wider your tires on the front the more 'vague' the steering will feel.

ie. I wouldn't go over 235 wide on the front of my GTSt

Then again tyre brand and quality is more important than overall size for handling

245's will easily fit on 7.5" wide rims.

I am not sure if 255's would fit on 7.5" though?

But as Tony said 255 wide tyres fit on a skyline easily with no troubles.

I had 235 front and 255 rear before and it didn't bring up the slip light.

I'll be running 245 and 265 next month :)

Silly question maybe, but why would different sized tyres bring up the slip light?

Do you mean different sized front to rear ?(I could understand it, if they were different diameter), or just different sized from standar all round?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...