Jump to content
SAU Community

Recommended Posts

Hello all.

I am expecting my 97 Stagea RS4 by the end of next week. I think I'll have the only one in Tassie but I could be wrong. I am having trouble finding a bolt in intercooler kit. Does anyone have any ideas? Do aftermarket R33 GTS-T Intercoolers fit?

Also if I buy a boost controller to up boost (I'm thinking Turbosmart E-Boost) will I need to get it re-tuned?

Oh and will an Apexi RSM be able to get rid of the 180kmh limit?

Any help would be awesome. I'm keen to find out heaps about these cars.

Thanks guys and girls.

Link to comment
https://www.sau.com.au/forums/topic/50959-nissan-stagea-intercooler/
Share on other sites

From what I can tell (I'm looking into this as well), the R33 GTS-t kits *should* be the same. Mind you, I've been looking at kits that bring the pipes back to the factory location so you can use the factory pipes from where they enter the engine bay.

There may be a difference in the kits that has the return pipe coming back into the engine bay under the battery/fuse box and then over the motor etc... As the Stagea's have the battery in the engine bay and the R33's don't, there's may be problems when cutting the hole for the return pipe...

J

Hi Iburkey22, am doing as J said, bringing the pipes back in the original location. The intercooler I am using flows top to bottom, not end to end like the usual Skyline intercoolers. So the intercooler inlet and outlet are both on the same side. It used to be in the front of our R32 GTST, and the pipes line up perfectly. It also looks like the bottom brackets will line up in the Stagea. The top brackets are completely different, but for the R32 GTST I fabricated my own anyway, so I will just make some more to fit the Stagea.

Consequently I am probably not a good example for you. I will post up some picures anyway when I do it, it's a few weeks away though. :D

what are the specs of your intercooler?

It's nothing special, it was an unused spare for a Production race car (a Toy... Toyo..... Toyot...... I can't seem to get it out). They had a "homologated" spec for racing, flows a bit better than the normal Supra one, but it really cools well. I have tried it up to 225 rwkw and it has a couple of PSI resistance, but I have plenty of PSI to spare, so it doesn't worry me. Best of all it's just sitting in the rack doing nothing, with all the pipework ready to go. Should only take a couple of hours to fit.

If it doesn't come up to scratch, I have an standard R32 GTR intercooler I can use, but I don't have any pipework, silicone hose or clamps for it. I used them all on the R32 GTST. Plus I would only get carried away and make up a set of pipes with 120 degree bend at the throttle body. Then I would need to change the BOV and all the little pipes and fittings. It's a 2 day job to get it right, when all the time I should be working on race cars, not tow cars.

Speaking of which, gotta go :cheers:

so do the supra ones have the inlet and outlet on the same side?

or am i interpreting what u said wrongly?

Yep, that's why I originally used it on the R32, it was easy, quick and cheap (as in free) and the pipework only took me an hour or so to fabricate. :D

would this mean less cutting out to fit the pipework into a stagea?

On the R32 GTST, I designed the alloy pipework so that it fitted straight up to the standard steel pipework, starting from where the standard intercooler was removed. If you look at it from the engine bay it is impossible to tell that an aftermarket intercooler was fitted. No "cutting" was required, so I can't see any reason why there would need to be any on the Stagea. There is heaps more room in there. But I won't know for sure until I remove the Stagea bumper bar and get into fitting it.

Hope that helps :D

Mad Wagon. I noticed in the pics you had an RSM on your dash.

I want one of these to get rid of the speed cut in my car. I just wanna wind her out on a desolate road near my house one time to see how fast she'll go. Plus I'll know how fast when my normal speedo goes off the clock. Do these work O.K.?

Thanks for your help so far. I'm very grateful. I think I'll go with the HKS kit I'll let you know how I get on.

Prepare to be bombarded with questions cobber.

Where did you buy it? How much? Who fitted it? Is it any good? What did you do with regard to the Battery? Relocate it to the boot or buy a smaller one?

I'm finally getting somewhere with this whole intercooler thing. It's great. Now I just need my friggin car. Ernest told me they would put it on a truck tomorrow but when I rang today he said they'd stuffed some paperwork up and I'd have to wait longer. I'M SICK TO DEATH OF WAITING!!! GRRRRR!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...