Jump to content
SAU Community

Recommended Posts

Hi all,

I just bought myself an r32 gtst, and ive got a few questions:

Where is the ambient temperature sensor for the climate control - cos the one in my car keeps reading 45.9 degrees no matter how cold it is :thumbsup:, and how would i go about finding a replacement part if its stuffed.

What does it mean if the HICAS light comes on - It has come on only twice since ive had it, and only when i've been drving for extended periods over 100kmph eg going down the freeway. Does it mean that the rear-wheel steering is on, or buggered??

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/51219-new-car-a-few-questions/
Share on other sites

top of the dash in front of the passenger is the ambient temp sensor. Try a second hand one from the forums, or a wreckers. There is a dignostic mode for the climate control as well...

HICAS light can mean a number of things...powersteering fluid, or brake fluid could be low. Need a wheel alignment.

o a diagnostic check on the HICAS as well....should narrow down the problems at least to give you somewhere to start.

hicas light shows when the hicas isnt working

ive got the same problem but mines on all the time

apparently its really common with the r32s

and for the climate control sensor u can pick one up from "Wally" at Zimports 8244 7911

179 South Terrace, Wingfield

he has heaps of standard parts at very good prices too!

I'd get rid of the HICAS, replacement kits are available for around $100, and then take the bulb out of the dash

Mine used to play up all the time, so it has been replaced with a solid bar, and it works really well - feels much more stable and predictable :rofl:

My ambient temp sensor is at the front of the car.

It used to be located where the FMIC now is. I simply moved it to the side a little.

The sensor on the top of the dash on the passenger side is a sunload sensor.

The sensor on the right hand side of the center console right next to the gearshifter boot is the in car temp sensor I believe.

They all go hand in hand working out the temps, where to blow cool and warm air etc :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...