Jump to content
SAU Community

R33 Reverse EL Dials

dazsQ

By dazsQ,
in Group Buys

 Share

Recommended Posts

  • Replies 204
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Mud Grand Master

Mud

Posted
Posted

Put mine in this morning,

But the speedo catches at about 40 and 60,

and the tacho catches at about 4000 rpm and wont go higher.

I have it all pulled apart agin now?

any suggestions?

I might use some hot glue to hold it down a bit better round the edges.

Mr_G Mentor

Mr_G

Posted
Posted

Hi guys, just installed mine, and works awesome!!! Here are a few little tips and tricks I did along the way:

Fed most of my wires through that gap on the RHS of the instrument cluster next to the taco. Saves taking connectors off and putting them back on...

http://www.skylinesaustralia.com/forums/at...achmentid=24826

Cut the wire for the EL Speedo, fuel and temp and fed the wire through the gap on the Top LH corner where the black wire on the back sits, then soldered the connector back on.

http://www.skylinesaustralia.com/forums/at...achmentid=24827

Rule number one!!! BE PATIENT and careful when installing the EL dials over the current dials, the Speedo/fuel/temp is the hardest one to do.... I found it was best to point the needles all at around an angle of 60 degrees

For wiring the power to the controller box, i tapped into my negative wire for my turbo timer... For postive, I ran it straight to the cigarette lighter. BE SURE TO TAP INTO THE SMALL CONNECTOR for positive

http://www.skylinesaustralia.com/forums/at...tid=24831&stc=1

I stuck my controller box next to my fuse board using double sided tape, makes things neater...

http://www.skylinesaustralia.com/forums/at...achmentid=24829

As someone else stated on here, you can select the colour you want, and then unplug the controller and leave it somewhere else. The controller is too ugly for my liking so I actually left the controller wire hanging out of the fuse board cover, sits nicely and you can plug up anytime and is sought of in a secret hideaway position...

http://www.skylinesaustralia.com/forums/at...achmentid=24828

And the finished product:

http://www.skylinesaustralia.com/forums/at...tid=24830&stc=1

arm85 Community Regular

arm85

Posted
Posted

Shit while doing it i snapped the clear plastic infront of the speedo and tacho and that, anyone know where i can get another one quick!!

Also how do i get to the boost guage? do i have to unsrew the tacho from the back?

Mud Grand Master

Mud

Posted
Posted
Ok I fixed it,  

I used a pair of scissors to GENTLY pry the needle out a bit so it clears the dial

No I didn't,

It seems there is a bit of "play" in the tacho needle.

If I pull gently on it , it comes out and clears the dial. after awhile it must vibrate back in and is now catching around 5000rpm.

and ideas friends?

arm85 Community Regular

arm85

Posted
Posted
No I didn't,

It seems there is a bit of "play" in the tacho needle.

If I pull gently on it , it comes out and clears the dial. after awhile it must vibrate back in and is now catching around 5000rpm.

and ideas friends?

Yeah just took mine for a spin and it does the same starts catching at about 3/3.5 and keeps stuterering as im accelerating, maybne the screws in the back of the tacho may have something to do with it but im not sure anyone got any other ideas??

Mr_G Mentor

Mr_G

Posted
Posted
Yeah just took mine for a spin and it does the same starts catching at about 3/3.5 and keeps stuterering as im accelerating, maybne the screws in the back of the tacho may have something to do with it but im not sure anyone got any other ideas??

I found mine was catching on the TACO round 5000rpm and jutters all the way to 6.5-7k, then jutters back as I let off the accelerator...

Pulled the dash out again and wiggled the taco needle up abit and spun it a fair few times and tried pushing down the EL dial more...

Seems to have worked :(

INASNT Grand Master

INASNT

Posted
Posted

Theres are good but after about a year of heavy use you will find the inverter will start to play up and the backlight will start to flciker while driver with the lights on and if you have other things on like the a/c, rear demister, or wipers.

If you guys installed them yourselfs i bet you speedo and tachs are around 200-300rpm out.

INASNT Grand Master

INASNT

Posted
Posted
inasnt so wat exactly are youy trying to say?....

i think i should get someone to install them

since everyone is startin to have problems with installin them

Pay extra and get someone that knows what they are doing to install em, coz once you *** the springs on the speedo and tach even a little the speedo and tach will always read wrong. My oil pressure gauge sometimes decide to read 0 when there is full oil pressure since i did my conversion

<line_up> Collaborator

<line_up>

Posted
Posted

I just put mine in and put some glue on EL tacho towards the bum of the needle and it aint catching, hopefully it doesnt, nut it is reading 150-200 rpm out when measured against my avcr, but they look awesome, i know motorware won install them on sklyines because they dont like to as its risky breaking the needle and other place are charging over $100

  • 1 month later...
R3AP3R Apprentice

R3AP3R

Posted
Posted

For the guys who were having problems with the needles getting stuck, has anyone got any good suggestions as to how to stop this from happening?

Glue has been mentioned, but I don't know whether it will be visible when they're lit.

Any suggestions would be appreciated.

Mr_G Mentor

Mr_G

Posted
Posted
For the guys who were having problems with the needles getting stuck, has anyone got any good suggestions as to how to stop this from happening?

Glue has been mentioned, but I don't know whether it will be visible when they're lit.

Any suggestions would be appreciated.

What I did was give my needles a good wiggle, well a hard one at that... Mine were originally catching(TACHO), but dont catch no more.

Not the most recommended of ways, but it worked for me and have had no problems since

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      Chris' Toyota Mark ii JZX110

      By Rezz · Posted

      Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Trailer got new mudguards to accommodate the new wheels Lightweight ally Painted, stickered and done ✅ 👌  
    • MBS206
      What accelerator cable can be used with greddy plenum

      By MBS206 · Posted

      Did you hit up the search function? R33 and greddy and cable returns this thread with some options.   https://www.sau.com.au/forums/topic/358214-rb25-throttle-body/
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      Thanks buddy.. the standard one needs to be about another inch or inch and a half longer. Thanks anyway
×
×
  • Create New...