Jump to content
SAU Community

Recommended Posts

hmm well i've lost two in the past two weeks, mabye the problem runs alittle deeper? i'm running r31 early eccs coilpacks and igniter with an r32 ecu, do you think the later model ecu could kill coilpacks? the igniter and coilpacks look identical to the 32 variaty apart from different electrical plugs on them. they stop working when they get hot only, so they dont entirely die (give it an hour and it comes back).

Whats the condition of the spring inside the coil?

Apparently these can crisp up a little causing problems.

Maybe thats what the problem is?

The spring gets hot looses its tension and doesn't make a proper contact.

GTR's are much better, as there igniter module provides much stronger spark. ND4SPD was running stock coils and module when it made 500rwkw, so it's more than doable. Pity they didn't make the GTS-t's/GTT's as good:(

Are you sure the ignitor is actually different on the GTR..? I think you will find they are the same.

mine shat themselves after 75000km went to split fires, compared them on a bench test to a known good RB coil and the difference was HUGE. The gap jumped by the spark was maxed out to 35mm, on the bench tester, and RPm wound up to 5000rpm and the thing was still sparking a big thick spark. Std RB coil couldn't hack it past 30mm and the spark was noticably thinner and weaker.

Not to mention no more break downs under boost :P

hmm well it seems i've got only .2v at the igniter on the cylinder thats not firing (no 4). i take it the igniter is on the earth side and acts as a big resistor to tame the voltage going through the ecu? so i'd guess its the contacts inside the coil getting too worn. sound feasible?

I've only had one coil die, #2 on my SeriesII R33 and i've been making over 300rwhp for a while now...fingers crossed the others don't follow suit...i've already sussed out splitfires if they do though :uh-huh:

how can u test which coils may be breaking down?

If it's breaking down at idle. Just take a plug of each coil until it makes no difference.

E.G, it will be running on 5 cylinders. When you pull the wrong plug it will run on 4, pull the faulty one, it will run on 5 still.

It wont blow up. The problem with the testing is that they very often don't work only intermittantly (spelling :(), also the consult will not see a problem even when it is actually happening.

I think you need to assume that they all need replacing or fixing because if one or two are stuffed now then another one or two might go soon just when you thought you had fixed it.

I'd imagine coils are a little like engine water hoses.

Once one goes the others follow soon after.

I had one develop a pin hole at the back of the head a few weeks ago. Since then 2 others have gone. All the little b*stards that are hard to get at.

If mine ever go i'll spend the extra $$ and get the good ones.

Well thats the way I have always done it.. on all my Skylines, and it's normally 1 or 2 that go, and you can normally find it on idle and pinpoint it.

I have never had to replace the whole lot on any Skylines in the past 5 Years or so.. :cheers:

I would like a nice set of spitfire coils.. but I can see better things to spend the money on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...