Jump to content
SAU Community

Recommended Posts

Hey guys just interested to find out how guys launch their beast at the drags.

Do you guys like to do a burnout to warm up yout tires or just get on with it?

And a question for the guys who have been down to the track for a run what are the impressions of other drivers of your beast?

:whackit:

:cheers:

Link to comment
https://www.sau.com.au/forums/topic/53722-launch-techniques/
Share on other sites

7700rpm against a launch limiter, release clutch

Thanks but not much help, the std rev limiter seems to be at 7,500 rpm and mine's an auto.

In the dry I stand on the brakes, hard. Stick it in drive and raise the revs until the torque converter holds the rpm there. Take foot of brake and floor the accelerator. No wheelspin from the standard engine just :wavey:

In the wet I ..... well exactly the same :wavey:

So I need more power then we might get some :burnout:

:cheers:

bring on the burning rubber.

when i see gtrs down at the drags or on dvd's when they warm up their tyres they always do a huge burnout, but they only smoke the rear tyres how does that work? are they in 2wd mode or something? or does using the brake to ensure you dont roll stop the front from spinning?

bring on the burning rubber.

when i see gtrs down at the drags or on dvd's when they warm up their tyres they always do a huge burnout, but they only smoke the rear tyres how does that work? are they in 2wd mode or something? or does using the brake to ensure you dont roll stop the front from spinning?

They stick them in 2wd to warm up the rear tyres as they cop most of the launch load. They have a line locker on the front brakes to hold them while the rears spin. :cheers:

I used to just hold the brake down while i floor the accel. after 4-5 secs wheels would start spinnin slow then after 30 secs a good amount of smoke was comin out from under, would keep going and gettin faster if i kept it there, but this was on 11psi and shell optimax with redex octane boost.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...