Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by GTR-80Y

MIZ as in girl !!! don't play dumb dude! hahaha:lol:

Actually, if i was as buff as u i would check myself out even more than i do now!

dont play dumb? LOL you got me there hahahhaa:lol:

who is she anyway? I only saw her name on this forum in the last few days and then out of nowhere I saw her car yesterday.

If you were buff as me then you will look like a condom full of walnuts! :lol:

Link to comment
https://www.sau.com.au/forums/topic/5430-hey-miz33t/#findComment-82918
Share on other sites

Originally posted by BY BY

no worries ombre..... when are you coming for a cruise again dood?

Ill be out of action for the next few weeks until Auto Salon is over

hey champ. your car going to be in the final battle?

I will be back in cruise action pretty much when you get back too.

I have a few things to sort out on my car.

Link to comment
https://www.sau.com.au/forums/topic/5430-hey-miz33t/#findComment-82943
Share on other sites

Nick, if i saw a chick in a skyline, the last thing i'd be lookin at is the friggin carbon bonnet. proof you're a hooooomoooooooo :)

who's entering auto salon?

i'm enterin as a demo car for a car audio place, but im going for the too low or whatever it is award. My exhaust shall scrape alllllll the way to homebush :)

*me pats angle grinder*

Link to comment
https://www.sau.com.au/forums/topic/5430-hey-miz33t/#findComment-83234
Share on other sites

Originally posted by XCUZME

Nick, if i saw a chick in a skyline, the last thing i'd be lookin at is the friggin carbon bonnet. proof you're a hooooomoooooooo :)

who's entering auto salon?

i'm enterin as a demo car for a car audio place, but im going for the too low or whatever it is award. My exhaust shall scrape alllllll the way to homebush :)

*me pats angle grinder*

haahha hi dudezz...

1. i am not dat new - ive been on d forum registered as 'ms---' for some time nowzz

2. its good 2 c 'some' ppl can recognise 'MIZ' = Female... saves me $378.00.

SDU4EVA - hi there,, sorry i didnt catch yah on my tail at regents pk - howeva i did at one stage drove pass a yellow GTT with YES... number plates......... waz dat u?

haehaeh dun worri BY BY - i am totally wif u - i wouldnt giv a winks eye abt any chic if there is a WHOOPIN HOT C/F bonnet slapped spanky clean and shiny on a skyline drivin pass... and yess... every nite i do kiss it goodnite too :)

yeopzz.... im in for final battlezz ... i'll c u guyzz dere!!

Link to comment
https://www.sau.com.au/forums/topic/5430-hey-miz33t/#findComment-83342
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...