Jump to content
SAU Community

Recommended Posts

I just saw on toymods a group buy for gearbox bell housing adaptors to fit w55 box to 4a motors, so it must be an issue with the weaker T50 box as you mentioned

I may have to read a bit more on this

I was also thinking about painting the AE86 Ford blueprint to match my R33

Are going to do the same?

  • Replies 154
  • Created
  • Last Reply

Top Posters In This Topic

I just saw on toymods a group buy for gearbox bell housing adaptors to fit w55 box to 4a motors, so it must be an issue with the weaker T50 box as you mentioned

I may have to read a bit more on this

I was also thinking about painting the AE86 Ford blueprint to match my R33

Are going to do the same?

HEHEHE your line blueprint too? cool

yeah . i dont know for sure about those boxes .. but i wouldn't want any power going through them!

jap spec ones would be a totally different issue.

it's my mates car, but me and his brother do nearly al the work on it.. so it's getting resprayed in red.

DAYUM , rb25 with 3040 would hammer in one of those.. would love to see that car go!

yeah . i dont know for sure about those boxes .. but i wouldn't want any power going through them!

jap spec ones would be a totally different issue.

apart from the clutch slave being on the opposite side they are the same. They are definitely strong enough for a n/a 20v... i have run one on my 20v for close to 3 years and it is still going strong.

apart from the clutch slave being on the opposite side they are the same.  They are definitely strong enough for a n/a 20v...    i have run one on my 20v for close to 3 years and it is still going strong.

cool, thats good news for Darrin ..

I am having a look at buy another ae86 this afternoon

genuine import Trueno

twin cam, P/steer, P/window, pop up head lights, disk brake LSD rar end, digital dash, white, 5 speed, air cond. complied approx 2 years ago 56,000km??

Has minor damage to front right corner

needs bonnet, head light and guard

Price $1500 ono :P

Had a look at toymods site, these things sell for approx $7000-12000.

Should be a bargin.

Even it is rough, I can always strip

Disc brake rear and LSD $1000

4age and g/box ecu $1500

Body and panels $1000-2000

interior and dash $500-800

mags $200-500

other parts $1000-2000

either way i can fix it and drive, the best option

Use the good parts in my other AE86 and sell the rest of the parts

Repair it and sell for $7000 plus

Too many options

The Trueno turned out to be a AE92 Trueno :rofl:

Never trust a women, no idea.

I have been doing some reading, the CA18det sounds like a good idea

Craved, have you got much further with yours

I have read your other posts about the conversion, It does not look too hard

Will the handbrake be fine in that location for daily use?

Why did you make a custom inlet plenum? Performance gain or install requirment.

Have you got many more pic's

Any more info would be great

other option is NA sr20de and 5 speed.

i was thinking of getting a ae86, but of course they are pretty rare here in vic, and seeing as i live about 2 hours outta melb that dont help either...

personally, i would like a sr20 redtop conversion into that beast and sha-zam! one fast little drift beast!

yeah, and i wouldnt mind if anyone knows of anyone else whos selling one eh?

-JL

Yeah there is one i found in brizvegas at banzai motorsport www.banzaimotorsports.com.au but it doesnt have a price listed for it.

y0 craved, my engine mount for the CA18 seems to be showin some stress due to engine twist. My fault I guess for doin some ghetto welds :) How much is the full engine and gearbox mount kit from where you got it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...