Jump to content
SAU Community

Recommended Posts

hey guys,

just after a few thoughts.

i've got a 88 r31 silhouette series 3. i want a bit of an upgrade as i want to start drifting. now here's what ive been thinking.

A: fit an rb20det and r32 g/box from a front cut to my car. will the brakes go on to the r31? is it worth getting the front cut or should i just get the engine g/box and loom. i'm a mechanic so i can do most of the work myself. will it be pretty staight forward? what would be the best option for the diff? i'd prefer the r32 engine over the r31 imports, because of the higher power rating.

or

B: just go out and buy an r32 gts-t.

i know the latter is a hell of alot easier, but i want something a bit different.

i think in the end it will probably work out about the same cost.

do you reckon the r31 would make a good drifter. at least panels would be pretty cheap when i bend it. hey its inevitable. may aswell think ahead!!

thanks in advance

stew

Link to comment
https://www.sau.com.au/forums/topic/55370-what-to-do/
Share on other sites

This should be in the "classic skyline" section, but until someone moves it, then I guess we're posting in here.

I find it disturbing that you say you're a mechanic, but you aren't familiar with which parts are interchangable, or how much work is involved in doing an engine transplant!

The brakes from a 32 will not go straight onto the 31.

(Otherwise everyone would be doing it)

I'm curious as to why you want the RB20.

Have you considered turbocharging the RB30?

Link to comment
https://www.sau.com.au/forums/topic/55370-what-to-do/#findComment-1080288
Share on other sites

sky031, i don't see what's so disturbing about being a mechanic and not knowing what parts are interchangeable or knowing how much work is involved in an engine transplant.

i work for peugeot and as such we don't tend to get much nissan work through the shop so my knowledge on part interchangeability between nissans is not that thorough, hence my asking people who may have done this conversion.

nor have we had any customers booking in there 206's for an rb20/25/26 conversion so i'm a bit lacking in that department too. sorry.

but thanks for your reply.

why the rb20? i wouldn't mind something a bit revvy for a change, and my current engine's a bit shagged as it is so i don't really want to turbo it.

b2barker, nice thought, do you want to send me some cash?

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/55370-what-to-do/#findComment-1080889
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...