Jump to content
SAU Community

Recommended Posts

Personally, I am going with the SAFC 11 current version, for ~$400 this gives a good A/F ratio result. You can't play with ignition as the auto needs ignition retard to give smooth shifts and not overload the transmission with torque while changing gear (prolongs gearbox life). So looking at other options with ignition control capablity (EManage for example) is a waste of money.

Full ecu upgrades, Power FC for example, aren't on the cards for me as they have no programming for the auto. Sure they run the engine itself just fine, but not the auto for the reasons above.

I am looking at around 200 awkw (that's about double the standard kw) and I have seen plenty of SAFC's work perfectly well at that power level on other RB25DET's. So the decision is pretty easy for me.

Hope that helps:cheers:

http://www.bikirom.com/

do a plug in board to allow remaping a r34 rb25 neo

anyone know if its the same ecu in the neo equiped stagea's ?

what about the hardcore aftermarket ecu's like motec and autronic ? I have seen autronics control auto sr20s before .

what about the hardcore aftermarket ecu's like motec and autronic ? I have seen autronics control auto sr20s before .

Nope, they have no shift logic. What you can do is use one of their outputs to change gear. Stuff like at 60 kph change into second, at 120 kph change into third etc. This is OK for a drag car, but not realy "shift logic". Where you want smooth up and down changes, down hill, up hill, under load, cruising etc etc

I was told that the lines of code to get an auto to changes gears properly, all the time, was over 1,000 times more than that used to get the engine to run. That's why you can buy manual car ECU's easily, but very very few auto ECU's. In fact the only one I have seen is the Power FC for Toyota Chasers and my understanding is it has Toyota auto shift programming anyway.

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...