Jump to content
SAU Community

Recommended Posts

Can someone please confirm that is it a defect to have a NOS bottle in car but not connected and also can I complain against the cop if he breaks the BOV cover? I had my BOV covered with a sheet but the cop broke it….And is it defect to have a big rear view mirror? Though I didn’t get the defect coz the cop broke the BOV cover and I argued with him but he is always in my area so that he can defect me next time…

Help needed!!!

Link to comment
https://www.sau.com.au/forums/topic/56960-help-needed-a-cop-broke-my-bov-cover/
Share on other sites

I'd just leave it.

Dude you've got NOS attached to your car, obviously if he wanted to screw you he would have, but because he broke the sheet, he's let you go.

I'd say that's the only reason he let you go.

why do you wanna carry the bottle when its not hooked up, if u crash and the bottle get punctured and sparked, then u r ****ed, u'd be better off leaving the bottle @ home when not using it, almost like carrying unneccesary jerry-cans around, it just a risk

Not sure about that Bass, I've heard that it's ok to have a full NOS setup but the bottle must NEVER be in the car on the road, even if your driving to the drag's etc. It must be transported in another car. Best to check with your states road authority.

why do you wanna carry the bottle when its not hooked up, if u crash and the bottle get punctured and sparked, then u r ****ed, u'd be better off leaving the bottle @ home when not using it, almost like carrying unneccesary jerry-cans around, it just a risk

Another point, you are right that it's not the best idea but a common misconception is that NOS is flammable. Nitrous oxide by itself is non-flammable. However, the oxygen present in nitrous oxide causes combustion of fuel to take place more rapidly.

This wasn't really helped by a particular movie :kick:

I would *think* it'd all come down to how much he reasonably suspected there was something illegal in the cover. I mean if you have drugs in the seat they'll rip apart the seat no prob we all know that but does it extend to defects I'm not sure.

If the cover wasn't purely there to hide the BOV then I'd go complain - if anyone law or not broke stuff on my car i'd take it further - it's a man's car you don't mess with it no matter what :P

On the other hand you're defectable so maybe you should just cop it sweet - remove the bov if you're worried. (they're a pleb in the uniform, you're the pleb without and all that... )

Hi Flowed turbo, front mount intercooler, upgraded fuel pump, APEXi FC, upgrade clutch, intake, 3.5 inch exhaust, SPARCO race seats, 18 inch STICH wheels, 240Kw@wheels, NOS system...i've added few more pics of my car in my profile.... i am thinking of upgrading it to 400 KW now....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...