Jump to content
SAU Community

Recommended Posts

hey Ryosuke I have a 16" thermo on my R31 & works a treat

I might be able to get u one cheap but will have to look into it + u pay freight cost.

send me a PM if u want me to check into it (brand new by the way & not hot)

I am using a old mits colt thermo switch for the cut in/out, 85 deg (give/take) 5deg+/- 74 deg +/- 3 deg,

I had a 38mm exhust pipe made up thats 2" long placed in the top hose with the switch/nut welded into the pipe, as the clutch fans on the RB's run a heat clutch in them so there is no way to get a switch in there any other way + plastic tank on the Rad means the copper probe is not the best idea as u can bust the top rad outlet trying to over do the clamp to stop leaks

also the switch is a 1 pin switch so u will need to earth the pipe out so once the switch opens it earths out through the pipe

Hope that helps a little :(

Cheers Mike

ok i ll try and autobarn...pm sent Oz your explaination is abit complicated for me lol

i just had a fmic installed and now the car overheats....tried tightening the belts,removed thermostat,flushin but doesnt help with the engine temps

thats what i think aswell i havent measured it yet but lookin at pics i think it just fits(http://ausrotary.dntinternet.com/forums/vi...pic.php?t=52641)

ive also removed my whole air con setup and left one of the fans which was used for the air con it helps but its noisy and the amount of air is not enough so it must be the fan thats the problem

mazda rx7 88turbo

it started overheating after the whole engine was put back in incl the radiator

it had a fmic installed along with the removal of the air con

tried a number of things such as removal of thermstat,tightening pulley and flushin radiator and waterpump but havent really helped

i spin the clutch fan but it seems to be ok

If the motor has been fully rebuilt they do tend to run a little warmer due to them being tight. Probally not to this degree though.

When you start the car when its cold can you hear the clutch fan (should be louder when cold because the clutch oil runs to the bottom of hub). My point is it should be engaged when you first start the car.

After a couple of minutes it should dis-engage and go quiet. It should then re-engage when the motor comes up to temperature.

If the hub is functioning and your sure of that, it may be one of two problems.

If the radiator was removed and allowed to dry out so to speak from sitting empty while motor was getting worked on. It may have had some internal corrosion/sludge flake off the tanks and block some of the rows effecting cooling capability.

If you reverse flush the radiator, (the opposite way that they water normally runs) you may blow any debre/crap out of the radiator thats causing possible trouble.

If you are sure the radiator is fine as well. The next thing would be to look at the FMIC and how much it is impeding flow to the radiator.

If it is a large bar and plate and the only way to the radiator is through the cooler, my guess is this may be your problem.

I've fitted heap of coolers with never having any negative effects to engine temp but there has always been an alternate way for the radiator to get air flow, not just from through the cooler. (Not familiar with the setup you have so cant comment)

The only other things it could be is faulty water pump (unlikely) excessively retarted timing which causes manifold to glow red hot and overheat motor. (unlikely).

You have already mentioned that the thermastat is ok?

hey ryosuke if its only since the motors been rebuilt as RB30 power said they do run hotter after a rebuild but what was done side seals apex the hole lot with water seal kit??????

I would be sus of the motor build a bit, also has it only started after the cooler was fitted or after the engine was reconed????

AH FORGET I ASKED LOL I AM BLIND

yeah binky I have noticed the same thing with my car it the car idles a lot smoother & also the car runs a lot cooler then with the clutch fan I am running a inline switch in a 38mm diameter pipe thats 2" long in the top hose & it works a treat had to many probs with the copper prob leaking out around the top rad hose & didn't want to try & nip it up more as the RB 's run plastic tank's & was worryed about busting the tank outlet.

ALSO Ryosuke if u do go with a thermo fan KEEP THE FAN SHROUD on the rad just cut it a little so the thermo fan will fit on under it, it means that the fan will pull air through better, by the way sorry about my 1st post I though u had a line :D

lol RB30 power i dont really understand your explaination that much but when the engine was put it and i tried turnin the engine over i heard funny sounds from the clutch fan but now it doesnt make noises nomore...the engine has not been rebuilt as i had comp tested it and it was almost perfect comp

i think this will be my plan....get one of my old radiators service and rebuilt it....if it still overheats i ll go the thermos.....can someone explain to me the push and pull types of thermos?

yeah i want one anyone wanna trade?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...