Jump to content
SAU Community

Recommended Posts

Hi Guys

Strut Braces Group Buy 2!!!!!!!!!!

I have a friend who imports strut braces and I can get some good deal from him if I buy in bulk. This is the going rate

buy 5 for $65 each <----- Look only need five people now.

buy 10 for $65 each

buy 15 for $60 each

buy more than 20 $55

Postage is $13 for 1 and $20 for 2.

Here is the list of strut braces I can get

skyline

R33 front strut brace

R32 front and rear strut brace

Silvia

s13 front and rear strut brace

Supra

Fits JZ80 and 70 series front strut brace

Soarar

Fits on soarer twin turbo and non turbo front strut brace

If you guys are interested reply to this thread and tell me exactly what you want. It just makes administration work a little easy when it comes to organising everything. Sorting through PM/EMAILs/thread replies and SMSs is a nightmare :)

Over the next few days/week I will see how many people are interested and let you all know what the cost will be. If everthing goes good I will then need the money from the buyers and I will get the parts and send them out to you guys. If everyone pays up quickly the buyers should get their strut brace within 7 days.

TOTAL BUYER COUNT: 0

END DATE: 26/12/04 or earlier depending on the amount of buyers.

Link to comment
https://www.sau.com.au/forums/topic/58407-strut-braces-group-buy-2/
Share on other sites

btw guys i was involved in gb#1

the quality of these are excellent - better than the one i bought for my r33 off ebay (forget which company)

thanx Rafael - my gf now has her xmas present :D

btw guys i was involved in gb#1

the quality of these are excellent - better than the one i bought for my r33 off ebay (forget which company)

thanx Rafael - my gf now has her xmas present :rofl:

lucky girlfriend!!!

Im sure alot of people in this group buy wish they were your girlfriend right now :D

Well I only need 5 people now the get the strut braces for $65. Since we have got a bit off him lately I can get better prices :P ....

So as soon as there is 5 people I will go and get the braces.

we have

1) Trevvy r32 front brace

2) tikki169 r32 rear brace

3) drag-on silvia front and rear for s13 silvia

4) Black-Beast R33 front bar.

Deal done!!!

As soon as I get all the cash from the following people I will go and get the braces.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...