Jump to content
SAU Community

fit bleed valve and guage

JH32

By JH32,
in Engines & Forced Induction

 Share

Recommended Posts

adam 32 Grand Master

adam 32

Posted
Posted

open my bonnet for 5minutes and look (i have same engine as you:D)

it couldnt be easier...

id be a bit worried about installing that splitfire guage though. do a search on the forums they arent supposed to be too crash hot. meggala's blown engine due to over boosting was apparently partly due to a faulty splitfire guage

inark Grand Master

inark

Posted
Posted

lol grim

Cold air to an engine is like sex to a man… you can never get enough! And the more you get the more you want and the better you feel and perform. Ok, I think I’ve taken that analogy far enough…

JH32 Grand Master

JH32

Posted
  • Author
Posted

ahh well i took the easy way out :(

it's going to supertec in the morning to get the bleed valve, boost guage and blow off valve fitted ...

i couldn't be stuffed trying to do it myself, especially when i have exams and i just want the things to be in heheheh :(

cheers anyway mate :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Predator1
      Tomei gasket

      By Predator1 · Posted

      Didnt realise RB's had more then 1 head.
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...