Jump to content
SAU Community

Recommended Posts

CEF-ZLA

DSC_1589.jpg

Yup its backup for sale.

Waiting on Jairus to confirm or deny if his sponsors in NZ will let him buy the car which seems to be taking a while, so its backup cause i wanna get rid of it so i can get a cheaper car to maintain for drift.

As most people probably know by now the car is an ex KENWORKS garage car which is owned by Ken Satoh. This car is an AWESOME drifter and pretty damn quick off the mark and down the straight.

Could be used for Drift, Circuit or Drag quite easily and is a good base to build from considering the power from such few mods. If you want a shiney street car for showing off then this isnt for you.

Interior Specs:

  • East Bear Bucket Seat
  • Half Roll Cage
  • Omori Water Temp Gauge
  • Omori Oil Temp Gauge
  • Omori Oil Pressure Gauge
  • Blitz Boost Gauge
  • Greddy Boost Gauge (Bar)
  • Nardi Steering Wheel
  • Razor Gear Stick

Engine and Performance Specs:

  • R33 GTR RB26DETT (Custom Blue with Glitter effect)
  • Front Mount Intercooler
  • Custom Piping with GReddy Hoses and Clamps
  • Blitz SUS Power Mesh POD Filters
  • Stock R33 GTR ECU
  • Very Large Oil Cooler (Brand unknown)
  • 3" Straight Pipe from Front Pipes back
  • Power: 207rwkw @ 9psi with 472nm of Torque
    Performed on XTC Dyno

Driveline and Suspension Specs:

  • OS Giken Twin Plate Clutch
  • CUSCO Mechanical LSD
  • RB25DET Gearbox
  • R33 GTST/300ZX 5 Stud Brake Conversion
  • Kei-Office Adjustable Coilovers front
  • CUSCO Adjustable Coilovers rear
  • Adjustable Camber tops
  • CUSCO Strut Brace front
  • CUSCO Strut Brace rear
  • JIC Magic Upper Arms
  • JIC Magic Lower Arms
  • Aftermarket Tension Rods

Exterior Specs:

  • Full Genuine URAS Monkey Magic (Damage to front bar repairable)
  • 18x8.5 front, 18x9.5 rear STICH Chrome GULF Rims (can be replaced with 17s with price adjustment)
  • 93 Model Tail Light Assembly
  • Rolled Guards front and rear

Condition Notes:

  • Please check all the pictures as there are quite a few of them which show all the little scuffs and scratches and pin dents etc.
  • Car drives very well. Easily driven on the street.
  • Compression tests came back A.OK. with no drop across any of the pistons.
  • All fluids including Diff, Engine and Gearbox Oil were replaced 3 weeks ago
  • Tyres are no good and will need to be replaced
  • Heater and Air Con removed
  • Interior is ok. Dash is a little rough but everything else is fine. Part of center peice cut to fit the handbrake.

Very tough car. Looks tough... sounds tough.

Car is NOT registered and NOT complied.

Car CAN be complied and registered for road use but i havent got around to it and due to the reason im selling it, wont be able to.

Video of the car in action:

http://home.iprimus.com.au/fairy_princess/jairus3.WMV - right click and save as

PICS:

http://www.skylinesaustralia.com/photopost...414DSC_0980.jpg

http://www.skylinesaustralia.com/photopost...414Img_0871.jpg

http://www.skylinesaustralia.com/photopost...414IMG_0064.JPG

http://www.skylinesaustralia.com/photopost...14IMG_00241.JPG - small pin dent on guard and bonnet with minor surface rust (easily fixed)

http://www.skylinesaustralia.com/photopost...14IMG_00261.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0027.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0028.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0063.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0062.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0061.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0059.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0058.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0057.JPG

http://www.skylinesaustralia.com/photopost...414IMG_0056.JPG - dash

http://www.skylinesaustralia.com/photopost...414IMG_0055.JPG - dash scratches

http://www.skylinesaustralia.com/photopost...414IMG_0054.JPG - center control

http://www.skylinesaustralia.com/photopost...414IMG_0053.JPG - gauge cluster in dash

http://www.skylinesaustralia.com/photopost...414IMG_0052.JPG - cut away for handbrake

http://www.skylinesaustralia.com/photopost...414IMG_0051.JPG - scuff around keyhole on drivers side

http://www.skylinesaustralia.com/photopost...414IMG_0050.JPG - small dents on rear right door

http://www.skylinesaustralia.com/photopost...414IMG_0048.JPG - crack in rear bar

http://www.skylinesaustralia.com/photopost...414IMG_0047.JPG - so called exhaust :)

http://www.skylinesaustralia.com/photopost...414IMG_0045.JPG - adjustable tops

http://www.skylinesaustralia.com/photopost...a/500/41411.jpg - east bear bucket

http://www.skylinesaustralia.com/photopost...ta/500/4146.jpg - bucket back

http://www.skylinesaustralia.com/photopost...a/500/41441.jpg -back

http://www.skylinesaustralia.com/photopost/data/500/414glitter paint.JPG://http://www.skylinesaustralia.com/ph...itter paint.JPG - sparkly engine paint :)

http://www.skylinesaustralia.com/photopost...14IMG_00101.JPG - The ZEITT wheels

If you like to be different and stand out from the crowd then this is the one for you.

Price: $16800 firm and will chuck in your choice of a brand new AVCR or SAFC II (will be delivered to buyers door after purchase of car as is) or

$16000 with 17inch Zeitt rims

Contact: Nik 0422 930 505

Email: [email protected]

Serious buyers need only enquire... no joyriders or time wasters

Shipping can be arranged at the buyers expense if interstate. I believe its around the $836 mark to WA from Melbourne including insurance. Can find out definate prices on rail shipping if needed.

Link to comment
https://www.sau.com.au/forums/topic/60204-fs-88-cefiro-rb26dett-ex-kenworks/
Share on other sites

lol its all good.

damn 836? i dunno what that guy from NS.com was on about then he said the 180 i wanted would only be 460 or something to ship to melb.

will add that to the original post.

cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...