Jump to content
SAU Community

Recommended Posts

Hi,

Does anyone know the correct procedure for cleaning an HKS pod filter, the yellow one that looks like a big mushroom?

I have cleaned it out using the solvent part of the K&N kit, but I am wondering if it requires an oiling??? I don't think it does but if anyone knows please let me know.

Thanks in advance.

Sam.

Link to comment
https://www.sau.com.au/forums/topic/60959-cleaning-hks-filter/
Share on other sites

Hey BlueTwo....

Ive also got a HKS pod, except its got the green element..

These should not be cleaned - but replaced.

They come pre-oiled, and dont take too well to washing/cleaning.

Depending on driving conditions, i would change it every 15/20k...

Cost is about $70 from autobarn...

:D

Hey Gizmo,

Do you know if there is any difference between the green and the yellow one? The yellow one looks like a big sponge, with what seems to be a good capacity airflow through the matrix of fibres, quite a bit different from my panel K&N with it's cotton insert.

...The flow of the HKS is one of the best when compared to others..

However, regarding pods as well as any other filter - more/better air flow usually means less protection filtering elements.....as attested to the pod noise !!

So - conversely, the HKS pod filter also isnt one of the best in regards to protection. Its your choice what you are after.

Every 20k i also check the AFM and tubing for any particles - so far it is ok, but you need to change it at least every 20k to ensure you dont get any nasty surprises..

colour difference is mainly for show - however, some colours only come in some sizes...it all depends on the size of your pod..

http://www.hksusa.com/products/?id=787

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...